
	Trending ▼ ICSE CBSE 10th ISC CBSE 12th CTET GATE UGC NET Vestibulares ResFinder

2003 & 1997 Course Project Engineering & Management

3 pages, 46 questions, 0 questions with responses, 0 total responses,

	pune_eng	+Fave Message
	Profile Timeline Uploads Q & A

Home > pune_eng >

Instantly get Model Answers to questions on this ResPaper. Try now!
NEW ResPaper Exclusive!

Formatting page ...

Total No. of Questions : 12] [Total No. of Pages : 3 P1346 [3864]-282 B.E. (Instrumentation) PROJECT ENGINEERING AND MANAGEMENT (1997 & 2003 Course) Time : 3 Hours] [Max. Marks : 100 Instructions to the candidates: 1) Answers to the two sections should be written in separate books. 2) Neat diagrams must be drawn wherever necessary. 3) Figures to the right indicate full marks. 4) Assume suitable data, if necessary. 5) All questions are compulsory. SECTION - I Q1) a) Define the following terms w.r.t. Project i) Time Driven OR Cost Driven Project. ii) Lump-Sum Project. iii) Turnkey Project. iv) EPC Project. v) [10] Cost-Plus Project. b) Give the full form and scope in brief for following standards. i) ISA S-5.1. ii) ISA S-5.20. iii) SAMA. iv) [7] ASME. OR Q2) a) Name the following symbols. a) b) [5] c) d) e) b) Identify and Differentiate between following pair of symbols. 1a. 1b. 6 2a. FF 7 [4] 2b. P.T.O. c) Identify following Tags. i) ii) iii) iv) [4] FICV-100. LSHL-20. TDRT-100. TDCV-10. d) Draw the symbol for : i) ii) iii) iv) [4] Hydraulic Signal. Pneumatically Operated Control valve in Line. Safety Valve. Any Valve Fail Intermediate. Q3) a) Draw and explain PFD & P & ID for the simple Feed Back control of Heat Exchanger. [10] b) What are the responsibilities of a Project Manager? Elaborate with [7] examples. OR Q4) a) Draw a Typical Instrument Index Sheet? Elaborate its use in Project Engineering Documentation. [10] b) What is the importance of Pressure & Temperature Sheet? How it differs from Mechanical Flow Sheet. [7] Q5) a) Enlist the various important documents required for I & C group in Project Engineering. State its importance in 2-3 sentences each. [8] b) What is MBOM? How it differs from MBOM? Elaborate its importance in project engineering. [8] OR Q6) a) Explain Interdepartmental, Inter organizational and Multi agency interaction. [6] b) i) ii) Draw a simple flow control loop with minimum basic components & using ISA symbols. [4] Develop Loop wiring diagram for the same. [6] SECTION - II Q7) a) What is Hot commissioning & Cold commissioning of project? [4] b) What is FAT? Where it is Conducted? Enlist various test activities involved in FAT? [8] c) Prepare a sample FAT test report simple system you know. [3864]-282 2 [5] OR Q8) a) What is Competitive Bidding? How any suppliers are needed for it? What is the criterion for a acceptable supplier? [9] b) Draw the installation sketch for DP transmitter used for liquid flow measurement showing tubing connection and equalizing valves. [8] Q9) a) What is UTP cable? Give detailed category wise classification & use of [8] different UTP cables. b) Explain various Network Topologies with its advantages & disadvantages. [9] OR Q10) a) Explain the pneumatic component testing procedure of a Control Panel. [8] b) Draw and Explain consoles with all dimensional details. Q11) a) What are different life cycle phases? [9] [3] b) Explain steps involved in Conceptual Phase and Divestment Phase. [6] c) For the network shown below find the critical path. [7] OR Q12) a) Discuss various methods of project cost estimation with its success index. [6] b) Define following w.r.t. PERT. i) iii) [4] Optimistic Time. Pessimistic Time. ii) Most likely Time. iv) Expected Time. c) What is WBS? What is its use? Define and explain Mile stone planning? [6] xxxx [3864]-282 3

Formatting page ...

Tags : Pune, Engineering, University of Pune, Engineering question papers, Pune University, previous year question papers, question papers, india, model question paper, pune university paper pattern, pune university syllabus, old question papers

pune_eng chat

Horizontal lines at:
Guest Horizontal lines at:
AutoRM Data:
Box geometries: