
	Trending ▼ ICSE CBSE 10th ISC CBSE 12th CTET GATE UGC NET Vestibulares ResFinder

2003 & 1997 Course Project Eng. & Management

3 pages, 42 questions, 0 questions with responses, 0 total responses,

	pune_eng	+Fave Message
	Profile Timeline Uploads Q & A

Home > pune_eng >

Instantly get Model Answers to questions on this ResPaper. Try now!
NEW ResPaper Exclusive!

Formatting page ...

Total No. of Questions : 12] P1540 [Total No. of Pages :3 [3764] - 282 B.E. (Instru.) PROJECT ENGINEERING & MANAGEMENT (1997 & 2003 Course) Time : 3 Hours] [Max. Marks:100 Instructions to the candidates: 1) Answers to the two sections should be written in separate books. 2) Neat diagrams must be drawn wherever necessary. 3) Figures to the right indicate full marks. 4) Assume suitable data if necessary. 5) All questions are compulsory. SECTION - I Q1) a) Draw ISA symbols used in P & ID Diagram. i) Vacuum relief valve. iii) Pressure reducing regulator with external tap. iv) Level regulator with mechanical linkage. v) b) Two way valve fail close. ii) [10] Flow element in line. State the chronological steps in development of Project engineering document. [6] OR Q2) a) Draw ISA symbols used in P & ID Diagram. i) Ultrasonic guided signal. iii) Shared signal from field to control room. iv) Bias. v) b) Pneumatic signal line. ii) [10] High selector & High Limiter (SAMA) Symbol. List & Explain different categories of the Project. [6] P.T.O. Q3) a) Draw the Temperature Control Loop. Give naming convections for i) The Loop. ii) For the instruments as per ISA. [4] [2] [2] b) Prepare an Instrument Index Sheet for the Loop Drawn in Q.No. 3a.[4] c) Prepare the Specification Sheet in S-20 format for Thermocouple. [6] OR Q4) a) b) Q5) a) b) Explain the loop wiring diagram in Project Engineering. Support your answer with two examples. [10] Draw the Level Control Loop. Give naming convections for i) The Loop. ii) For the instruments as per ISA. [4] [2] [2] What are different types of Cables used in Plant instrumentation? Suggest suitable cables for Analog Signal & Data Signal justify your selection.[8] What is IOI? Explain the term networking with respect to IOI. [8] OR Q6) a) b) Prepare BOM for the Temperature Transmitter. [8] Explain the importance of Plant Layout & GA drawings for Instrument Project Engineering. [8] SECTION - II Q7) a) b) Enlist & Explain in Brief the documents required for commissioning activity. [8] Explain the Vendor Registration process. State its need. [8] OR Q8) a) b) Q9) a) b) What are the key points required to be considered while issuing the PO to the Supplier. [8] Prepare CAT for any Control Panel. [8] Prepare Typical Inspection report for the Control Panel. [9] Write short note on CPM & PERT? [9] [3764]-282 2 OR Q10)a) b) Draw & explain the control room layout with certain considerations.[9] Draw & explain the Installation of DP transmitter. Q11)Write brief notes on : a) Crash Time Concept. c) SOW. d) [16] WBS. b) [9] Project Estimates. OR Q12)a) Explain the following Standards in brief. i) API. iii) SAMA. iv) b) ISA. ii) [8] NEMA. Explain Gant Chart in detail. kbkb [3764]-282 3 [8]

Formatting page ...

Tags : Pune, Engineering, University of Pune, Engineering question papers, Pune University, previous year question papers, question papers, india, model question paper, pune university paper pattern, pune university syllabus, old question papers

pune_eng chat

Horizontal lines at:
Guest Horizontal lines at:
AutoRM Data:
Box geometries: