
	Trending ▼ ICSE CBSE 10th ISC CBSE 12th CTET GATE UGC NET Vestibulares ResFinder

GATE 2014 : Engineering Sciences

42 pages, 153 questions, 5 questions with responses, 5 total responses,

	gate	+Fave Message
	Profile Timeline Uploads Q & A

Home > gate >

Formatting page ...

GATE 2014 Examination XE: Engineering Sciences Duration: 180 minutes Maximum Marks: 100 Read the following instructions carefully. 1. To login, enter your Registration Number and password provided to you. Kindly go through the various symbols used in the test and understand their meaning before you start the examination. 2. Once you login and after the start of the examination, you can view all the questions in the question paper, by clicking on the View All Questions button in the screen. 3. This paper consists of 8sections: GA (General Aptitude), A (Engineering Mathematics), B (Fluid Mechanics), C (Materials Science), D (Solid Mechanics), E (Thermodynamics), F (Polymer Science & Engineering) and G (Food Technology). Section GA (General Aptitude) and Section A (Engineering Mathematics) are compulsory. Attempt any 2 sections out of the 6 optional Sections B through G. There are 10 questions carrying 15 marks in the compulsory General Aptitude (GA) section. Question numbers 1 to 5 of this section carry 1 mark each, and question numbers 6 to 10 carry 2 marks each. There are 11 questions carrying 15 marks in Section A(Engineering Mathematics). Question numbers 1 to 7 of this section carry 1 mark each, and question numbers 8 to 11 carry 2 marks each. Each of the other sections (Sections B through G) contains 22 questions carrying 35 marks. In each of these sections, question numbers 1 to 9 carry 1 mark each and question numbers 10 to 22 carry 2 marks each. 4. Depending upon the GATE paper, there may be useful common data that may be required for answering the questions. If this paper has such useful data, the same can be viewed by clicking on the Useful Common Data button that appears at the top, right hand side of the screen. 5. The computer allotted to you at the examination center runs specialized software that permits only one answer to be selected for multiple-choice questions using a mouse and to enter a suitable number for the numerical answer type questions using the virtual keyboard and mouse. 6. Your answers shall be updated and saved on a server periodically and also at the end of the examination. The examination will stop automatically at the end of 180 minutes. 7. In each paper a candidate can answer a total of 65 questions carrying 100 marks. 8. The question paper may consist of questions of multiple choice type (MCQ) and numerical answer type. 9. Multiple choice type questions will have four choices against A, B, C, D, out of which only ONE is the correct answer. The candidate has to choose the correct answer by clicking on the bubble ( ) placed before the choice. 10. For numerical answer type questions, each question will have a numerical answer and there will not be any choices. For these questions, the answer should be entered by using the virtual keyboard that appears on the monitor and the mouse. 11. All questions that are not attempted will result in zero marks. However, wrong answers for multiple choice type questions (MCQ) will result in NEGATIVE marks. For all MCQ questions a wrong answer will result in deduction of marks for a 1-mark question and marks for a 2-mark question. 12. There is NO NEGATIVE MARKING for questions of NUMERICAL ANSWER TYPE. 13. Non-programmable type Calculator is allowed. Charts, graph sheets, and mathematical tables are NOT allowed in the Examination Hall. You must use the Scribble pad provided to you at the examination centre for all your rough work. The Scribble Pad has to be returned at the end of the examination. Declaration by the candidate: I have read and understood all the above instructions. I have also read and understood clearly the instructions given on the admit card and shall follow the same. I also understand that in case I am found to violate any of these instructions, my candidature is liable to be cancelled. I also confirm that at the start of the examination all the computer hardware allotted to me is in proper working condition . GATE 2014 SET- 1 General Aptitude -GA Q. 1 Q. 5 carry one mark each. Q.1 A student is required to demonstrate a high level of comprehension of the subject, especially in the social sciences. The word closest in meaning to comprehension is (A) understanding Q.2 (B) meaning (C) concentration (D) stability Choose the most appropriate word from the options given below to complete the following sentence. One of his biggest ______ was his ability to forgive. Q.3 (B) virtues (C) choices (D) strength 20 14 (A) vice Rajan was not happy that Sajan decided to do the project on his own. On observing his unhappiness, Sajan explained to Rajan that he preferred to work independently. Which one of the statements below is logically valid and can be inferred from the above sentences? (A) Rajan has decided to work only in a group. (B) Rajan and Sajan were formed into a group against their wishes. (C) Sajan had decided to give in to Rajan s request to work with him. (D) Rajan had believed that Sajan and he would be working together. Q.4 If y = 5x2 + 3, then the tangent at x = 0, y = 3 (A) passes through x = 0, y = 0 (C) is parallel to the x-axis E A foundry has a fixed daily cost of Rs 50,000 whenever it operates and a variable cost of Rs 800Q, where Q is the daily production in tonnes. What is the cost of production in Rs per tonne for a daily production of 100 tonnes? G AT Q.5 (B) has a slope of +1 (D) has a slope of 1 Q. 6 Q. 10 carry two marks each. Q.6 Find the odd one in the following group: ALRVX, EPVZB, ITZDF, OYEIK (A) ALRVX Q.7 (C) ITZDF (D) OYEIK Anuj, Bhola, Chandan, Dilip, Eswar and Faisal live on different floors in a six-storeyed building (the ground floor is numbered 1, the floor above it 2, and so on). Anuj lives on an even-numbered floor. Bhola does not live on an odd numbered floor. Chandan does not live on any of the floors below Faisal s floor. Dilip does not live on floor number 2. Eswar does not live on a floor immediately above or immediately below Bhola. Faisal lives three floors above Dilip. Which of the following floor-person combinations is correct? (A) (B) (C) (D) GA (B) EPVZB Anuj 6 2 4 2 Bhola 2 6 2 4 Chandan 5 5 6 6 Dilip 1 1 3 1 Eswar 3 3 1 3 Faisal 4 4 5 5 1/2 GATE 2014 SET- 1 General Aptitude -GA Q.8 The smallest angle of a triangle is equal to two thirds of the smallest angle of a quadrilateral. The ratio between the angles of the quadrilateral is 3:4:5:6. The largest angle of the triangle is twice its smallest angle. What is the sum, in degrees, of the second largest angle of the triangle and the largest angle of the quadrilateral? Q.9 One percent of the people of country X are taller than 6 ft. Two percent of the people of country Y are taller than 6 ft. There are thrice as many people in country X as in country Y. Taking both countries together, what is the percentage of people taller than 6 ft? (A) 3.0 (C) 1.5 (D) 1.25 The monthly rainfall chart based on 50 years of rainfall in Agra is shown in the following figure. Which of the following are true? (k percentile is the value such that k percent of the data fall below that value) E 20 14 Q.10 (B) 2.5 G AT (i) On average, it rains more in July than in December (ii) Every year, the amount of rainfall in August is more than that in January (iii) July rainfall can be estimated with better confidence than February rainfall (iv) In August, there is at least 500 mm of rainfall (A) (i) and (ii) (C) (ii) and (iii) (B) (i) and (iii) (D) (iii) and (iv) END OF THE QUESTION PAPER GA 2/2 GATE 2014 ENGINEERING MATHEMATICS (COMPULSORY) XE-A A : ENGINEERING MATHEMATICS ( COMPULSORY) Q. 1 Q. 7 carry one mark each. Q.1 If 1, 0, and -1 are the eigenvalues of a 3 3 matrix A, then the trace of A 2 5 A is equal to ______________. Which of the following is a solution of the differential equation x 2 y ' ' xy ' y 4 sin(ln x), x 0 ? (A) (B) (C) (D) Q.3 y 2 x sin(ln x ) y 2 x sin(ln x ) y 2 ln x cos(ln x ) y 2 ln x cos(ln x) 20 14 ) Q.2 At z 0 , the complex function f ( z ) z | z | 2 Q.4 AT E (A) satisfies the Cauchy-Riemann equations and is differentiable (B) satisfies the Cauchy-Riemann equations but is not differentiable. (C) does not satisfy the Cauchy-Riemann equations but is differentiable. (D) does not satisfy the Cauchy-Riemann equations and is not differentiable. Ten chocolates are distributed randomly among three children standing in a row. The probability that the first child receives exactly three chocolates is 5 211 39 5 210 (B) 39 1 (C) 9 3 1 (D) 3 XE (G (A) Q.5 Let the function f : [0, 5] R be defined by 0 x 1 2 x 5, f (x ) 2 x 2 5, 1 x 2 2 3 23 2 x 5. 3 x 3 , The number of points where f is not differentiable in (0, 5) , is ___________. XE-A 1/3 GATE 2014 Q.6 ENGINEERING MATHEMATICS (COMPULSORY) XE-A An integrating factor of the differential equation (3 x 2 y 3e y y 3 y 2 ) dx ( x 3 y 3e y xy ) dy 0 is 1 y 1 (B) 2 y 1 (C) 3 y (D) ln y (A) (A) (B) (C) (D) ( 2, 11) ( 1, 2) ( 1, 4) ( 2, 23) Q. 8 Q. 11 carry two marks each. Q.8 20 14 ) If a cubic polynomial passes through the points (0, 1), (1, 0), (2, 1) and (3, 10), then it also passes through the point Let the function f : [0, ) R be such that f ( x) (A) [0, 1] (B) [2, 3] (G (C) [4, 5] 2 AT f (1) lies in the interval 8 for x 0 and f (0) 1. Then x 3x 4 E Q.7 (D) [6, 7] Q.9 The perimeter of a rectangle having the largest area that can be inscribed in the ellipse XE x2 y2 1 , is ________. 8 32 Q.10 XE-A If the work done in moving a particle once around a circle x 2 y 2 4 under the force field F ( x, y) (2 x ay) i (2 y ax) j is 16 , then a is equal to _________. 2/3 GATE 2014 Q.11 ENGINEERING MATHEMATICS (COMPULSORY) XE-A 1 2 0 1 Let r and s be real numbers. If A 2 0 3 and b 1 , then the system of linear r s 0 s 1 equations AX b has 20 14 ) (A) no solutions for s 2r . (B) infinitely many solutions for s 2 r 2 . (C) a unique solution for s 2r 2 . (D) infinitely many solutions for s 2r 2 . XE (G AT E END OF THE QUESTION PAPER XE-A 3/3 GATE 2014 FLUID MECHANICS XE-B B : FLUID MECHANICS Q. 1 Q. 9 carry one mark each. Q.1 A dam with a curved shape is shown in the figure. The cross sectional area of the dam (shaded portion) is 100 m2 and its centroid is at x = 10 m. The vertical component of the hydrostatic force, Fz , is acting at a distance x p . The value of x p is ____ m. 14 ) z Fz xp 20 40 m G x O E x Q.2 AT 15 m ( ) 6 xyt For an unsteady incompressible fluid flow, the velocity field is V = 3 x 2 + 3 t i j , where x , y are in meters and t is in seconds. Acceleration in m/s2 at the point x = 10 m and y = 0 , as (G measured by a stationary observer is (A) 303 (C) 43 (D) 13 For an incompressible flow, the existence of components of acceleration for different types of flow is described in the table below. XE Q.3 (B) 162 Type of Flow Components of Acceleration P: Steady and uniform Q: Steady and non-uniform R: Unsteady and uniform S: Unsteady and non-uniform 1: Local exists, convective does not exist 2: Both exist 3: Both do not exist 4: Local does not exist, convective exists Which one of the following options connecting the left column with the right column is correct? (A) P 1; Q 4; R 3; S 2 (B) P 4; Q 1; R 2; S 3 (C) P 3; Q 2; R 1; S 4 (D) P 3; Q 4; R 1; S 2 XE-B 1/8 GATE 2014 Q.4 FLUID MECHANICS XE-B Velocity in a two-dimensional flow field is specified as: u = x 2 y ; v = y 2 x . The magnitude of the rate of angular deformation at a location ( x = 2 m and y = 1 m) is ____ s-1. Q.5 For a plane irrotational flow, equi-potential lines and streamlines are (C) at an angle of 45o to each other. Q.6 (B) at an angle of 90o to each other. (D) at an angle of 60o to each other. 14 ) (A) parallel to each other. Flow around a Rankine half-body is represented by the superposition of (B) source and uniform flows. (C) vortex and uniform flows. (D) source, vortex and uniform flows. 20 (A) source and vortex flows. It is required to carry out model studies on a boat having a characteristic length of 3.6 m and travelling at a speed of 3 m/s. Assume the acceleration due to gravity as 10 m/s2 and neglect the effects due to viscous and surface tension forces. The value of appropriate non-dimensional number is ____. Q.8 Which one of the following velocity profiles typically represents a fully developed incompressible, turbulent flow in a pipe? XE (G AT E Q.7 (A) XE-B (B) (C) (D) 2/8 GATE 2014 Q.9 FLUID MECHANICS XE-B Consider an incompressible, laminar flow past a circular cylinder of diameter d . The flow is uniform at the far upstream. Which one of the following figures typically represents the wake velocity profile just downstream of the cylinder? d d (B) 14 ) (A) d 20 d (D) XE (G AT E (C) XE-B 3/8 GATE 2014 FLUID MECHANICS XE-B Q. 10 Q. 22 carry two marks each. Q.10 A container of square cross-section is partially filled with a liquid of density 1 . The cylinder is intended to float in another liquid of density 2 as shown in the figure. The distance between metacentre and centre of buoyancy is I , where I and Vsub are area moment of inertia of the Vsub 14 ) cross-section and submerged volume, respectively. Neglect the weight of the container. 20 h b (C) 2 b h + 1 1 > 0 6 1 h b 2 (B) 2 b h 1 + 1 > 0 6 1 h b 2 (D) 2 b h + 1 + 1 > 0 6 1 h b 2 (G In a steady state two-dimensional potential flow field due to a point source, the acceleration of a particle at a distance r from the point source is XE Q.11 2 b h 1 1 > 0 6 1 h b 2 AT (A) E Which one of the following is the correct condition for stability? (A) proportional to r 1 . (C) a constant. Q.12 (B) proportional to r . (D) proportional to r 3 . and location ( x, y ) is described as: + ( x 1) V= 3t 2 i j . The equation for the path line of a particle passing through the point (1,0) at Velocity in a two-dimensional flow at time t t = 0 is 0 (A) x 4 4 y 3 = (C) XE-B ( x 1) 4 64 y 3 = 0 (B) ( x 1) (D) ( x + 1) 3 4 2 y4 = 0 16 y 3 = 0 4/8 GATE 2014 Q.13 FLUID MECHANICS XE-B The gravity driven flow over a hump of height h in a canal is shown in the figure. The height of the free surface from the canal bed at upstream of the hump is H . The free surface height reduces to H1 above the hump. H1 H h (A) (B) 2 ( 1 ) 1 1 2 2 1 2 1 1 ( 1 + )2 2 20 (C) (D) AT E 2 ( 1 ) 1 1 ( 1 + )2 2 2 ( 1 ) 1 1 2 2 1 Steady state incompressible flow through a pipe network is shown in the figure. Inlets marked as (1), (2) and (3) and exit marked as (4), are shown with their respective diameters. The exit flow rate at (4) is 0.1 m3/s. A 20% increase in flow rate through (3) results in a 10% increase in flow rate through (4). The original velocity through inlet (3) is _____ m/s. (G Q.14 14 ) Assuming the canal bed to be horizontal, the discharge per unit width is given by XE (3) (2) 5 cm 10 cm (4) (1) XE-B 5/8 GATE 2014 FLUID MECHANICS XE-B A reducing elbow is used to deflect water upward by 30o as shown in the figure. The mass flow rate at the inlet is 14 kg/s. Water is entering at a gauge pressure of 200 kPa and exits to the atmosphere. The cross-sectional area is 113 cm2 at the inlet and 7 cm2 at the exit. Density of water and acceleration due to gravity are 1000 kg/m3 and 10 m/s2, respectively. Magnitude of x - component of the water force on the elbow is ____ N. Q.16 A source with a strength of k1 and a vortex with a strength of k2 are located at the origin. The 14 ) Q.15 Q.17 k1 + k2 r (B) 2 k12 + k2 r (C) 2 k12 k2 (D) r E (A) 20 resultant velocity at a radial distance r from the origin due to the superposition of the source and vortex is expressed as ( k1 k2 r ) Velocity potential for an incompressible fluid flow is given as: = 2 x 2 + 2 y y 2 . Assume the is ____. (G The model of a conduit is scaled to 1/100 of the actual size. Seawater is used in the prototype and fresh water is used in the model. Velocity in the prototype is 0.5 m/s. Density and dynamic viscosity of the seawater are 1025 kg/m3 and 1.07 10-3 kg/m-s, respectively. Density and dynamic viscosity of fresh water are 1000 kg/m3 and 1 10-3 kg/m-s, respectively. Assume the viscous forces to be dominant. The velocity to be maintained in the model to ensure dynamic similarity is____ m/s. XE Q.18 AT value of stream function at the origin to be zero. The value of stream function at [ ( x, y ) ( 2, 2 ) ] Q.19 XE-B A fluid is flowing through a pipe of circular cross-section. Reynolds number of the flow is 1600. The head loss over a 45 m length of the pipe is 0.6 m. The average flow velocity of the fluid is 1 m/s and the acceleration due to gravity is 10 m/s2. The diameter of the pipe is ____ m. 6/8 GATE 2014 Q.20 FLUID MECHANICS XE-B Consider a laminar flow over a flat plate of width w . At Section 1-1, the velocity profile is uniform as shown in the figure. The x -direction velocity profile at Section 2-2 is given by 2 u y y = 2 , where is the boundary layer thickness. U 1 U 2 y u ( y) 1 2 The volume flow rate through Section 2-2 is given by (B) 1 U w 3 (C) U w (D) 2 U w 3 20 Q.21 1 U w 2 14 ) x (A) U A cube of weight W and side a falls at a constant speed in a medium as shown in the figure. If the E medium is air (mass density = air ) let U air be the velocity of the cube. If the medium is water AT (mass density = water ) let U water be the velocity of the cube. (G a XE W Neglecting the buoyancy force and assuming drag coefficient to be same for both cases, the ratio of U air is given by U water velocities, (A) XE-B air water (B) air water (C) water air (D) 1 7/8 GATE 2014 Q.22 FLUID MECHANICS XE-B Water is flowing through a venturimeter having a diameter of 0.25 m at the entrance (Station 1) and 0.125 m at the throat (Station 2) as shown in the figure. A mercury manometer measures the piezometric head difference between Stations 1 and 2 as 1.3505 m. The loss of head between these two stations, is 1/7 times the velocity head at the Station 2. Assume the acceleration due to gravity to be 10 m/s2. The velocity of water at the throat is ____ m/s. diameter 0.25 m diameter 0.125 m 2 14 ) 1 AT E 20 Mercury Manometer XE (G END OF THE QUESTION PAPER XE-B 8/8 GATE 2014 MATERIAL SCIENCE- XE-C C : MATERIALS SCIENCE Useful constants : 6.023 x 1023 mol-1 : 1.38 x 10-23 J.K-1 : 1.6 x 10-19 C : 9.1 x 10-31 kg : 8.314 J.mol-1.K-1 : 3 x 108 m.s-1 : 6.63 x 10-34 J.s Avogadro s Number Boltzmann s constant, k Electron Charge, e Electron rest mass, mo Universal gas constant, R Speed of light, c Planck s constant, h 1 eV = 1.6 x 10-19 J Q.1 Neoprene is rendered non-inflammable because Q.2 20 (A) it has a highly cross-linked structure (B) it has a highly linear chain structure (C) of the presence of chlorine atom in the structure (D) of the absence of chlorine atom in the structure 14 ) Q. 1 Q. 9 carry one mark each. Nylon-6 is manufactured from At room temperature, the typical barrier potential for silicon p-n junction in Volt (V) is (A) 0.7x10-23 Q.4 AT Q.3 E (A) caprolactum (B) adipic acid and hexamethylene diamine (C) maleic anhydride and hexamethylene diamine (D) sebasic acid and hexamethylene diamine (B) 0.07 (D) 7.0 Quantitative measurement of the roughness of a polysilicon wafer can be performed with (G (A) scanning tunneling microscopy (C) transmission electron microscopy Q.5 (C) 0.70 (B) scanning electron microscopy (D) atomic force microscopy The temperature of the antiferromagnetic-to-paramagnetic transition is called (B) Curie-Weiss temperature (D) Debye temperature XE (A) Curie temperature (C) Neel temperature Q.6 At low injection level, a forward biased p-n junction would have (A) no charge carriers (B) minority carrier concentration much more than majority carrier concentration (C) minority carrier concentration equal to majority carrier concentration (D) minority carrier concentration much less than majority carrier concentration Q.7 Which of the following mechanical properties of a material depend on the mobile dislocation density in it. (P) Young s modulus (Q) yield strength (R) ductility (S) fracture toughness (A) P, Q, R Q.8 (B) Q, R, S (C) P, R, S (D) S, P, Q The equilibrium concentration of vacancies in a pure metal (A) increases exponentially with temperature (B) decreases exponentially with temperature (C) varies linearly with temperature (D) is independent of temperature XE-C 1/4 GATE 2014 Q.9 MATERIAL SCIENCE- XE-C The materials belonging to which one of the following crystal classes would be both piezoelectric and ferroelectric (A) 222 (C) 1 (B) 4mm (D) 2/m Q. 10 Q. 22 carry two marks each. Polymerized isotactic polybutadiene has a molecular weight of 3 x 105 g/mol. The degree of polymerization is _______________. Q.11 A bar of Ti with Young s modulus of 110 GPa and yield strength of 880 MPa is tested in tension. It is noticed that the alloy does not exhibit any strain hardening and fails at a total strain of 0.108. The mechanical energy that is necessary to break the material in MJ/m3 is ____________. Q.12 A copper cup weighing 140 g contains 80 g of water at 4 C. Specific heats of water and copper are 4.18 and 0.385 J/g C, respectively. If 100 g of water that is at 90 C is added to the cup, the final temperature of water in C is ______________. Q.13 Match the reaction in Column I with its name in Column II. 20 14 ) Q.10 E L liquid, , , different solid solution phases (P) L + (Q) L + (R) + Q.15 Match the composite in Column I with the most suitable application in Column II. Column I (P) Glass fibre reinforced plastic (Q) SiC particle reinforced Al alloy (R) Carbon-carbon composite (S) Metal fibre reinforced rubber (A) P-4, Q-5, R-1, S-2 (C) P-5, Q-4, R-1, S-3 XE-C (B) P-2, Q-1, R-4 (D) P-4, Q-2, R-3 The Young s modulus of a unidirectional SiC fiber reinforced Ti matrix composite is 185 GPa. If the Young s moduli of Ti and SiC are 110 and 360 GPa respectively, the volume fraction of fibers in the composite is _________. XE Q.14 (G (A) P-1, Q-4, R-3 (C) P-2, Q-3, R-1 Column II (1) peritectic (2) eutectic (3) monotectic (4) eutectoid AT Column I Column II (1) Missile cone heads (2) Commercial automobile chasis (3) Airplane wheel tyres (4) Car piston rings (5) High performance skate boards (B) P-3, Q-5, R-2, S-4 (D) P-4, Q-2, R-3, S-1 2/4 GATE 2014 Q.16 MATERIAL SCIENCE- XE-C Which among the following rules need to be satisfied for obtaining an isomorphous phase diagram in a binary alloy system? (P) The atomic size difference should be less than 15%. (Q) Both the end components should have the same crystal structure (R) The valency of the end components should be the same. (S) The end components should have dissimilar electronegativities (A) P, Q, R Q.17 (B) Q, R, S (C) R, S, P (D) S, P, Q The energy in eV and the wavelength in m, respectively, of the photon emitted when an electron in a hydrogen atom falls from n = 4 to n = 2 state is (B) 2.55, 0.365 (C) 2.75, 0.451 (D) 2.55, 0.487 14 ) (A) 3.0, 0.413 The weight in kg of gallium (Ga) to be mixed with arsenic (As) for obtaining 1.0 kg of gallium arsenide (GaAs) is ______________. (MGa = 69.72 g/mol; MAs = 74.92 g/mol) Q.19 Match the material in Column I with the property in Column II (A) P-1, Q-2, R-3, S-4 (C) P-4, Q-1, R-2, S-3 (B) P-2, Q-3, R-4, S-1 (D) P-2, Q-1, R-4, S-3 AT Relevant portion of a binary phase diagram of elements A and B is shown below. The mass fraction of liquid phase at 1000 C for an alloy with 15 wt.% B is ___________. XE (G Q.20 Column II (1) Shape memory alloy (2) Piezoelectric ceramic (3) High temperature superconductor (4) Optoelectronic semiconductor E Column I (P) Pb(Zr,Ti)O3 (Q) Ni50Ti50 (R) GaAs (S) YBa2Cu3O7 20 Q.18 Q.21 XE-C The expected diffraction angle (in degrees) for the first order reflection from the (113) set of planes for face centered cubic Pt (lattice parameter = 0.392 nm) using monochromatic radiation of wavelength 0.1542 nm is ___________. 3/4 GATE 2014 Q.22 MATERIAL SCIENCE- XE-C The diffusion coefficients of Mg in Al at 500 and 550 C are 1.9x10-13 and 5.8x10-13 m2/s respectively. The activation energy for diffusion of Mg in Al in kJ/mol is ___________. XE (G AT E 20 14 ) END OF THE QUESTION PAPER XE-C 4/4 GATE 2014 SOLID MECHANICS XE-D D: SOLID MECHANICS Q. 1 Q. 9 carry one mark each. Q.1 A steel wire of diameter 5 mm is bent around a cylindrical drum of radius 0.5 m. The steel wire has modulus of elasticity of 200 GPa. Find the bending moment in the wire in N-m. d = 5 mm 14 ) R = 0.5 m A compressed air tank having an inner diameter of 480 mm and a wall thickness of 8 mm is formed by welding two steel hemispheres. If the allowable shear stress in the steel is 40 MPa, find the maximum permissible pressure (in MPa) inside the tank. Q.3 The Euler s buckling load of a column fixed at both the ends is P. If one of the ends is made free, the buckling load shall change to E 20 Q.2 (C) P/4 (D) P/2 A point in a body is subjected to a bi-axial state of stress, equal in magnitude but opposite in nature. On a plane inclined at an angle 45 with respect to x-axis (passing through the point), the (G Q.4 (B) P/8 AT (A) P/16 XE (A) shear and normal stresses are zero (B) normal stress is maximum and shear stress is zero (C) shear stress is maximum and normal stress is zero (D) shear stress is maximum and normal stress is non-zero XE-D 1/9 GATE 2014 Q.5 SOLID MECHANICS XE-D A weightless beam subjected to two point loads is shown in the figure below. 10 kN 1m 10 kN 1m 2m The shear force diagram of the beam is 10 kN 14 ) (A) 10 kN 10 kN (B) 20 10 kN 5 kN (C) 5 kN E 5 kN 10 kN For the pin jointed truss, find the axial force (in kN) in the member 2-5. XE (G Q.6 AT (D) XE-D 2/9 GATE 2014 The supporting structure of a water tank is made of reinforced concrete (RC) with a tubular cross section of inner diameter di, outer diameter do, height l, and Young s modulus E. The mass of the tank is m. If mass of the supporting structure is neglected, then the natural frequency of the water tank in transverse direction is 4 3 4 (A) 64 3 4 384 4 (C) ) Q.8 (B) 360 3 4 4 (D) 8 3 4 4 64 3 A mass is attached to a spring and placed horizontally in a frictionless surface. A simple pendulum has been pivoted to the mass. The degree of freedom of this system is 14 ) Q.7 SOLID MECHANICS XE-D 20 X y E l (B) 2 (C) 3 (D) 4 XE (G (A) 1 AT x XE-D 3/9 GATE 2014 Q.9 SOLID MECHANICS XE-D Consider the following two statements Statement 1: A body of weight W falls from a height h and strikes the ground. If the body starts from rest, the velocity with which it strikes the ground is 2 , where g is the acceleration due to gravity. W 14 ) h 20 Statement 2: If the same body (initially at rest) slides without friction along an inclined plane PQ (angle of inclination ) starting from an elevation h above point Q, then its velocity at point Q is 2 P W E h AT Q The correct option is (G (A) Both statements 1 and 2 are true (B) Statement 1 is true and 2 is false (C) Statement 1 is false and 2 is true XE (D) Both statements 1 and 2 are false XE-D 4/9 GATE 2014 SOLID MECHANICS XE-D Q. 10 Q. 22 carry two marks each. Q.10 A composite bar of length L is made of a centrally placed steel plate (50 mm wide x 10 mm thick) with two copper plates (each 30 mm wide x 5 mm thick) connected rigidly on each side. If the temperature of the composite bar is raised by 50 C, find the stress developed in each copper plate in MPa. (For Steel: Es = 2x105 MPa and s= 12x10-6 / C; For Copper: Ec = 1x105 MPa and c= 17x10-6 / C) Copper plate 5 mm Steel plate 10 mm Copper plate 14 ) 5 mm Q.11 20 L The vertical deflection at the free end of the cantilever beam as shown in figure is 100 kN EI = flexural rigidity (B) 1400/3EI (C) 200/EI (D) 100/EI AT (A) 1400/EI 1m E 2m A hollow shaft and a solid shaft have the same length and the same outer radius R. The inner radius of the hollow shaft is 0.6 R. Assuming that both the shafts are made of same material and are subjected to the same torque, find the ratio of shear stress in hollow shaft to that in solid shaft. Q.13 A beam with overhangs carries one point load acting downwards and the other upward. The clockwise moment Pb is applied at each support. The bending moment at the midpoint of the beam is XE (G Q.12 Pb P b (A) 0 XE-D Pb L (B) PL/2 P b (C) PL (D) PbL 5/9 GATE 2014 Q.14 SOLID MECHANICS XE-D A cantilever beam of length L supports a concentrated load P at the free end. The cross section of the beam is rectangular with constant width b and varying depth h. The depth h of this idealized cantilever beam varies in such a way that the maximum normal stress at every cross section remains equal to the allowable bending stress. Considering only the bending stresses, the depth hx of the fully stressed beam at any distance x from the free end shall vary P L (C) linearly with x (D) with cube of x A cantilever beam is subjected to following three different loading conditions: (a) a concentrated load P at its free end, (b) a couple Mo at its free end and (c) both loads acting simultaneously 20 Q.15 (B) with square root of x 14 ) (A) with square of x P L AT E (a) Mo L (G (b) P Mo L (c) XE The flexural rigidity of the beam may be assumed as EI. The strain energy due to bending when both loads act simultaneously (A) can be determined by applying the principle of superposition and the strain energy is 2 3 6 + 2 2 (B) can be determined by applying the principle of superposition and the strain energy is 2 2 6 + 3 2 (C) cannot be determined by applying the principle of superposition and the strain energy is 2 3 6 + 2 2 + 2 2 (D) cannot be determined by applying the principle of superposition and the strain energy is 2 2 6 XE-D + 3 2 + 2 2 6/9 GATE 2014 Q.16 SOLID MECHANICS XE-D A tapered rod has diameter d1 at one end which reduces uniformly to a diameter d2 over the length (L). If the modulus of elasticity of the material is E, the change in the length of the rod due to the application of axial force (P) is (A) 4 (B) 1 2 4 2 2 1 2 (C) (D) 1 2 2 2 2 1 2 y= 50 MPa and For a point in a body subjected to a plane stress condition ( x= 100 MPa, xy = yx = 25 MPa), the maximum principal stress in MPa is_____________ Q.18 An isotropic body is subjected to a state of stress given by: x= 10 MPa and xy = yx = 20 MPa. Assuming G = 0.4E, the volumetric strain is (C) 10/E (D) 15/E A block of weight Q rests on an inclined plane and it is attached to a string which runs over a frictionless pulley to carry a block of weight P at its other end. The coefficient of friction between the block of weight Q and the inclined plane is . Consider the following cases: Case I: weight Q starts moving down the inclined plane Case II: weight P starts falling down (G AT E Q.19 (B) 7.5/E 20 (A) 5/E 14 ) Q.17 The limiting values of ratio P/Q for Case I and Case II respectively are (sin cos ) ( sin cos ) (sin + cos ) ( sin + cos ) XE (A) (B) (C) (D) XE-D and and and and (sin + cos ) ( sin + cos ) (sin cos ) (sin cos ) 7/9 GATE 2014 Q.20 SOLID MECHANICS XE-D To unload an item from a truck a crane boom is raised with a constant angular velocity of 1 rad/s relative to the cab and then the cab is rotated about a vertical axis with constant angular velocity of 0.5 rad/s. Z Boom P Cab 45 Y 14 ) O X (C) 5 2 2 + 2 (B) + 2 (D) 5 2 2 + 2 + 2 AT XE y (A) 12.54 at 30 XE-D 2 5 A block of mass 5 kg moves up on a smooth inclined plane with a velocity of 10 m/s in the direction shown. A bullet of mass 60 g travelling at 500 m/s strikes the block centrally and gets embedded in it. The velocity of the block and embedded bullet in m/s immediately after the impact is (G Q.21 2 2 5 E (A) 20 If the length of the boom (OP) is 10 m, the velocity of the tip (P) of the boom in m/s is 10 m/s 30 x 500 m/s (B) 13.84 at 51.78 (C) 13.84 at 30 (D) 15.62 at 51.78 8/9 GATE 2014 A balloon with ballast (weight) inside it has a gross weight of 500 N. It is falling vertically with a constant acceleration of 2 m/s2. If air resistance is negligible, find the weight of ballast (in N) that must be thrown out in order to give the balloon an upward acceleration of 2 m/s2. (Acceleration due to gravity, g = 9.81 m/s2) 14 ) Q.22 SOLID MECHANICS XE-D E 20 500 N XE (G AT END OF THE QUESTION PAPER XE-D 9/9 GATE 2014 THERMODYNAMICS XE-E E : THERMODYNAMICS Notations used: P-pressure, V-volume, T-temperature, S-entropy, H-enthalpy, U-internal energy, cp-specific heat at constant pressure, cv-specific heat at constant volume; specific properties are designated by lower case symbols. Subscripts: R-reduced, C-critical, f-saturated liquid, g-saturated vapor, Properties of air: cp = 1.005 kJ/(kg.K), specific heat ratio = 1.4, Gas constant = 0.287 kJ/(kg.K), Molecular weight = 29 gm/mol. 14 ) Universal gas constant = 8.314 kJ/(kmol.K). Q. 1 Q. 9 carry one mark each. Entropy is a (A) Path function (C) Property independent function Q.2 A small container has gas at high pressure. It is placed in an evacuated space. If the container is punctured, work done by the gas is (A) Positive (B) Negative (C) Zero (D) E The molecular weight of a mixture is 38.4 gm/mol. The mixture is composed of methane and carbon-dioxide gases. The atomic weights of the elements C, H, and O are 12, 1, and 16 gm/mol, respectively. The mole fraction of methane (Xmethane) is ____________ and that of carbon-dioxide (X carbon-dioxide) is _______. AT Q.3 (B) Point function (D) Neither path nor point function 20 Q.1 Q.4 (G (A) Xmethane = 0.2; X carbon-dioxide = 0.8 (B) Xmethane = 0.8; X carbon-dioxide = 0.2 (C) Xmethane = 0.3; X carbon-dioxide = 0.7 (D) Xmethane= 0.7; X carbon-dioxide = 0.3 A system undergoes a change from state 1 to state 2. During this process, the change in the internal energy is U. The change in internal energy of the system when executing the cycle 1-2-1 is equal to (B) 2 U (C) Zero (D) 2 U XE (A) U XE-E 1/5 GATE 2014 Q.5 THERMODYNAMICS XE-E Which among the following plots represents a line joining two states with the same dew point temperature on a standard psychrometric chart, with the dry bulb temperature on the X-axis and the humidity ratio on the Y-axis? (C) (D) (A) 1.5 Q.7 (B) 2.5 u dv v T u (B) du = c p dT + dP P T (D) 3.5 AT (C) du = cv dT + u dv v T (G (D) du = cv dT The minimum and maximum volumes in an air standard Otto cycle are 100 and 800 cm3. Its thermal efficiency (%) is (B) 94.55 XE (A) 56.47 Q.9 (C) 0.4 For a superheated vapor that cannot be approximated as an ideal gas, the expression determining a small change in the specific internal energy is (A) du = c p dT + Q.8 20 The efficiency of a reversible engine operating between two temperatures is 40 % . The COP of a reversible refrigerator operating between the same temperatures is E Q.6 (B) 14 ) (A) (C) 54.08 (D) 87.50 At a saturation temperature Tsat, the difference between the entropy of saturated vapor and entropy of saturated liquid can be expressed as ( (C) (u ) )T ( (D) (u (A) h f hg Tsat g uf )T u ) T (B) hg h f sat f g sat sat Q. 10 Q. 22 carry two marks each. Q.10 A gas in a closed system is compressed reversibly from an initial volume of 0.2 m3 to 0.1 m3 at a constant pressure of 3 bar. During this process, there was a heat transfer of 50 kJ from the gas. The change in internal energy of the gas during this process in kJ is (A) 20 XE-E (B) 80 (C) 80 (D) 20 2/5 GATE 2014 In a closed rigid vessel, air is initially at a pressure of 0.3 MPa and volume of 0.1 m3 at 300 K. A stirrer supplies 100 kJ of work to the air, while 20 kJ of heat is lost to the atmosphere across the container walls. After these processes, the temperature of air changes to _________K. (A) 321.9 Q.12 (B) 702.4 (C) 782.4 (D) 620.2 A reversible heat engine (E) operates using three thermal reservoirs with temperatures as shown in the following figure. If Q1=Q2, the efficiency of the engine is ___________. Reservoir 1 T1 = 1200K Reservoir 2 T2 = 600 K W E Q2 20 Q1 14 ) Q.11 THERMODYNAMICS XE-E Q3 (A) 17.28 Q.14 (C) 0.625 (D) 0.75 A metal block of mass 25 kg at 300 K is immersed in an infinitely large liquid nitrogen bath maintained at 77 K. The system comprising of the block and liquid nitrogen attains thermal equilibrium. The average specific heat of the metal is 0.45 kJ/(kg.K). The entropy generated during the process is ___________kJ/K. (G Q.13 (B) 0.125 AT (A) 0.25 E Reservoir 3 T3 = 300 K (B) 32.5 (C) 47.8 For a gas obeying the equation of state given by P + (D) 47.8 a v = RT , the values of the critical v2 XE volume and the critical temperature are 0.004 m3/kg and 100 C, respectively. If the value of the gas constant is 250 J/(kg.K), then the value of the constant a is _____________ (N.m4/kg2). Note that the critical point is the point of inflection on the critical isotherm. (A) 124.3 XE-E (B) 0.75 (C) 186.58 (D) 248.67 3/5 GATE 2014 A rigid closed vessel is initially filled with 2 kg of water which is a mixture of saturated liquid and saturated vapor states at 2 bar. The vessel is placed in an oven which heats the mixture to the critical state. Using the saturated and critical property values from the table given below, the heat transferred from the oven to the vessel is __________kJ. Pressure = 2 bar vg (m3/kg) uf (kJ/kg) 0.8857 504.49 Critical pressure vc (m3/kg) uc (kJ/kg) 0.003155 2029.6 3 vf (m /kg) 0.0010605 (A) 3035.8 Q.16 (B) 3040.6 ug (kJ/kg) 2529.5 (C) 3036.2 (D) 3044.9 2 The equation of state for a certain gas is given by v = RT / P C1 / T + C2 , where C1 is 50,000 (K2.m3)/kg and C2 is 0.8 m3/kg. The relation 14 ) Q.15 THERMODYNAMICS XE-E h v = v T is known for the gas. The inversion P T T P h = 0 is _________K. P T (A) 500.0 (D) 250.0 E (B) 14.920 (C) 2.809 (D) 1.809 The thermal efficiency of an air standard Brayton cycle 0.35. The pressure ratio across the turbine is (A) 4.516 (B) 5.232 (C) 7.535 (D) 8.234 Steam is isentropically expanded in a turbine from 80 bar to 7 bar. At the inlet of the turbine (state 1) h1 is 3246 kJ/kg and s1 is 6.52 kJ/(kg.K). (G Q.19 (C) 353.6 The maximum pressure and temperature in an air standard diesel cycle are 44 bar and 1600 K, respectively. If the minimum pressure and temperature are 1 bar and 300 K, respectively, then the cut-off ratio (the ratio of the volume at the end of the heat addition process to that at the beginning of the heat addition process) is (A) 1.000 Q.18 (B) 433.0 AT Q.17 20 temperature, given by the condition, XE hf (kJ/kg) 697 Pressure = 7 bar hg (kJ/kg) sf [kJ/(kg.K)] 2763 2.0 sg [kJ/(kg.K)] 6.7 The enthalpy of the steam exiting the turbine (state 2) in kJ/kg is (A) 2683.87 XE-E (B) 2657.17 (C) 1986.87 (D) 3354.17 4/5 GATE 2014 Q.20 THERMODYNAMICS XE-E A thin insulating membrane separates two tanks initially filled with nitrogen [mean cv = 21.6 J/(mol.K)] and carbon-dioxide [mean cv = 11.6 J/(mol.K)] as shown below. Perfect insulation 0.8 moles of N2 at 2 bar and 350 K 0.2 moles of CO2 at 1 bar and 300 K (A) 344.1 (C) 325.0 (D) 346.1 Two moist air streams MAS1 and MAS2 are mixed adiabatically. The details of MAS1 and MAS2 are given below in the table. h (kJ/kg of dry air) v (m3/kg of dry air) Flow rate (m3/min) 20 Q.21 (B) 306.3 14 ) The membrane is ruptured and the gases are allowed to mix to form a homogeneous mixture at equilibrium. During this process there are no heat or work interactions between the tank contents and the surroundings. The final temperature at the equilibrium state in Kelvin is MAS1 42 0.85 85 MAS2 80 0.9 90 Q.22 (B) 61 (C) 81 AT (A) 122 E With pressure remaining same and with no work interactions during the mixing process, the enthalpy of the mixed stream is ________________ kJ/kg of dry air. (D) 108 Consider the steady flow of air through an insulated nozzle. The pressure and temperature at the inlet are 120 kPa and 320 K, respectively. The outlet pressure is 1 bar. The inlet velocity is very small and the air undergoes a reversible adiabatic process. The outlet velocity, in m/s, is (B) 180.7 (C) 5.7 (D) 127.3 (G (A) 303.7 XE END OF THE QUESTION PAPER XE-E 5/5 GATE 2014 POLYMER SCIENCE AND ENGINEERING XE-F F : POLYMER SCIENCE AND ENGINEERING Q. 1 Q. 9 carry one mark each. Q.1 The estimation of the molecular weight of a polymer by gel permeation chromatography (GPC) is based on its (A) polarity (C) adsorption to stationary phase Q.2 (B) size (D) crystallinity Elastomers are characterized by (A) (B) H S =T (C) H S = 1.5T (D) H S = 2T The tensile strain of a uniformly extending plastic specimen of initial length L0 and extended length L is (A) Q.5 S = 0.5T 0 (B) 0 E Q.4 H 20 Thermodynamically, two polymers with enthalpy of mixing ( H) and entropy of mixing ( S) form a miscible blend at temperature T when (C) AT Q.3 14 ) (A) high modulus and high elongation at break (B) high modulus and low elongation at break (C) low modulus and high elongation at break (D) low modulus and low elongation at break 0 0 (D) 0 0 In natural rubber compounding, a peptizer is added Q.6 (G (A) at the beginning of the compounding cycle (B) after the addition of filler (C) at the end of the compounding cycle (D) after the addition of antioxidant A continuous annular product is produced by XE (A) compression molding (C) blow molding Q.7 Relate the three varieties of polyethylene in the left column with their chain structures given in the right column. P. HDPE Q. LDPE R. LLDPE (A) P-1, Q-3, R-2 Q.8 (B) extrusion (D) injection molding 1. long as well as short branches 2. only short branches 3. no branches (B) P-3, Q-2, R-1 (C) P-2, Q-3, R-1 Match the following changes observed in the calorimetric analysis of a polymer sample when heat flow (y-axis) is plotted against temperature (x-axis): P. step increase in heat flow Q. exothermic peak R. endothermic peak 1. crystallization 2. melting 3. glass transition (A) P-1, Q-2, R-3 XE-F (D) P-3, Q-1, R-2 (C) P-3, Q-1, R-2 (B) P-2, Q-1, R-3 (D) P-3, Q-2, R-1 1/4 GATE 2014 Q.9 POLYMER SCIENCE AND ENGINEERING XE-F A Bingham plastic fluid is flowing under gravity, down a vertical plate, as a film. Find the appropriate match for the fully developed velocity profile of the fluid in the film, from among those shown below. (A) (B) x air y film =0 (C) (D) x film air x air =0 20 y film air AT E =0 y film y 14 ) =0 x (G Q. 10 Q. 22 carry two marks each. Calculate the mass percent of the crystalline phase in a polymer sample of density 975 kg/m3. The density of amorphous phase is 866 kg/m3 and that of the crystalline phase is 996 kg/m3. Q.11 Find the rate of initiation (molL-1s-1) of a polymerization reaction using a peroxide initiator with a half life of 0.1 s and efficiency of 70%, if the concentration of the initiator is 0.05 molL-1. XE Q.10 Q.12 The constitutive equation of a shear thinning polymeric fluid is given by = 0 1 + ( 0 ) where represents shear stress (Pa), and , the corresponding shear rate (s-1). The quantities 0 = 20 Pas and 0 = 10 s 1 are constants. Find the apparent viscosity of the sample (Pas) when the applied shear rate is 40 s-1. XE-F 2/4 GATE 2014 Q.13 POLYMER SCIENCE AND ENGINEERING XE-F Identify the monomer for the polymer shown below prepared by ring opening metathesis polymerization. (B) 20 (A) (D) E (C) Q.14 14 ) n The most appropriate order of toughness of nylon based materials is The shear rates involved in calendering ( cal), compression molding ( comp), extrusion ( ext), and injection molding ( inj) processes follow the order (G Q.15 AT (A) talc filled nylon < dry nylon < wet nylon (B) dry nylon < wet nylon < talc filled nylon (C) wet nylon < dry nylon < talc filled nylon (D) wet nylon < talc filled nylon < dry nylon (B) comp < ext < cal < inj (D) comp < cal < ext < inj XE (A) inj < cal < ext < comp (C) comp < inj < ext < cal Q.16 The dynamic mechanical response of a thermoplastic automotive component has shown a loss angle of 45 and storage modulus of 3500 MPa. Calculate the loss modulus (MPa) of the component. Q.17 Match the terms in Column A with the appropriate terms in Column B: Column A P. processability Q. moisture permeation R. hardness S. fracture toughening (A) P-3; Q-4; R-2; S-1 (C) P-4; Q-3; R-1; S-2 XE-F Column B 1. Rockwell scale 2. rubber modification 3. melt flow index 4. Fick's law (B) P-3; Q-4; R-1; S-2 (D) P-4; Q-3; R-2; S-1 GATE 2014 Q.18 POLYMER SCIENCE AND ENGINEERING XE-F Match the following additives for plastics with their respective functions: Additive P. dilaurylthiodipropionate Q. graphite R. antimony trioxide S. carbon fibre (A) P-4; Q-1; R-2; S-3 (C) P-4; Q-1; R-3; S-2 3/4 (B) P-1; Q-4; R-2; S-3 (D) P-1; Q-4; R-3; S-2 Catalyst/initiator P. butyl lithium Q. TiCl4 + Et3Al R. CuBr S. H2SO4 (A) P-2; Q-1; R-4; S-3 (C) P-3; Q-1; R-4; S-2 14 ) Match the following catalyst/initiator with the type of polymerization reaction: Polymerization reaction 1. Ziegler-Natta 2. cationic 3. anionic 4. atom transfer radical polymerization 20 Q.19 Function 1. solid layer lubricant 2. flame retardant 3. reinforcement 4. antioxidant (B) P-2; Q-4; R-1; S-3 (D) P-3; Q-4; R-1; S-2 For AIBN (mol. wt. = 164 gmol-1) initiated free radical polymerization of methyl methacrylate (mol. wt. = 100 gmol-1), where the termination is only by radical coupling, the of PMMA is found to be 4636 gmol-1. Calculate the degree of polymerization. Q.21 A polymer solution is made by dissolving 5 g of polymer in 1000 ml of solvent. The flow time of the solvent and that of the polymer solution between two appropriate marks in a viscometer are 40 s and 60 s, respectively. The reduced viscosity (in dLg-1) of the polymer solution is: (C) 1.0 I END OF THE QUESTION PAPER XE-F (D) 1.5 The volume resistivity of a polymeric material is 107 m. Find the resistance (in M ) of a cube of the material of side 1 cm. The direction of current flow is as shown in the figure below. XE Q.22 (B) 0.50 (G (A) 0.25 AT E Q.20 GATE 2014 POLYMER SCIENCE AND ENGINEERING XE-F XE (G AT E 20 14 ) 4/4 XE-F GATE 2014 FOOD TECHNOLOGY XE-G G: FOOD TECHNOLOGY Q. 1 Q. 9 carry one mark each. The systematic name of sucrose is (A) -D-Fructofuranosyl (1 2) -D-Glucopyranoside (B) -D-Glucopyranosyl (1 2) -D-Fructofuranoside (C) -D-Glucopyranosyl (2 1) -D-Fructofuranoside (D) -D-Fructofuranosyl ((2 A non-hydrolyzable lipid is (A) Lecithin Q.3 (B) Arachidic acid The respiratory quotient (RQ) for the reaction 2 C57H110O6 + 163 O2 (A) 0.70 (B) 1.14 (G (B) Aspartame (C) Sucralose (D) 0.14 (D) Vitamin E (D) Cyclamate The objective of heating milk to about 65 C before homogenization is to inactivate (B) Lipases (C) Lactases (D) Invertases XE Make the correct match of the processes in Column I with the suitable materials/products in Column II Column I Column II 1) Rendering 2) Hydrogenation 3) Degumming 4) Bleaching P) Lecithin Q) Fullers earth R) Lard S) Margarine (A) 1-R, 2-P, 3-Q, 4-S (B) 1-P, 2-Q, 3-S, 4-R (C) 1-R, 2-P, 3-S, 4-Q XE-G 114 CO2 + 110 H2O is Which of the following non-nutritive sweeteners contains similar calories per gram as that of sucrose? (A) Glucose oxidase Q.7 (C) Vitamin K AT (B) Vitamin D (A) Saccharin Q.6 (D) Tristearin Liver necrosis may be caused by the deficiency of (A) Vitamin A Q.5 (C) 1.43 E Q.4 (C) Tocopherol 20 Q.2 1) -D-Glucopyranoside 14 ) Q.1 (D) 1-R, 2-S, 3-P, 4-Q 1/5 GATE 2014 Q.8 FOOD TECHNOLOGY XE-G A fruit juice of viscosity and density is agitated using an impeller of diameter D at a speed of N P revolutions per minute. The terms = N 3 D 5 , Y = D2 N , Z= 2 represent three process related numbers, where P is power imparted by impeller and g is acceleration due to gravity. Which of the following is correct representation of these numbers? (A) X = Power, Y= Froude, Z = Reynolds (C) X = Froude, Y= Reynolds, Z = Power (D) X = Reynolds, Y = Power, Z = Froude The energy required to reduce the size of a food material from a mean diameter of 12 mm to 4 mm is 10 kJ kg-1. From Rittingers law, the energy needed to reduce the same material from a diameter of 1.2 mm to 0.4 mm in kJ kg-1 is __________ 14 ) Q.9 (B) X = Power, Y = Reynolds, Z = Froude Q. 10 Q. 22 carry two marks each. Q.11 Saccharomyces cerevisiae (mean doubling time 3.2 h) is grown in a batch fermenter with an operating volume of 12 m3. A 2% (v/v) inoculum, which contains 5 kg cells per 100 m3 is mixed with the substrate. The residence time in the fermenter is 24 h and the density of broth is 1010 kg m-3. The mass of S. cerevisiae obtained from the fermenter, in kg, is ________ 20 Q.10 Make the correct combination of operations in Column I with the machines in Column II Column II P) Pin mill Q) Rubber rolls R) Break rolls S) Screw press AT E Column I 1) Rice milling 2) Wheat milling 3) Mustard oil expelling 4) Pepper grinding (A) 1-Q, 2-R, 3-S, 4-P (C) 1-Q, 2-P, 3-S, 4-R (D) 1-Q, 2-R, 3- P, 4- S The correct order for D121 values of the spores of food spoilage bacteria in aqueous medium is (G Q.12 (B) 1-R, 2- Q, 3-S, 4-P (A) B. stearothermophilus > C. sporogenes > C. botulinum type A > B. coagulans (B) C. sporogenes > B. stearothermophilus > C. botulinum type A > B .coagulans XE (C) C. botulinum type A > B. stearothermophilus > C. sporogenes > B. coagulans (D) B. stearothermophilus > C. botulinum type A > C. sporogenes > B. coagulans Q.13 Make the correct combination of pigments/microorganisms in Column I with the process/ products in Column II Column I 1) Anthocyanin 2) Chlorophyll 3) Bacillus subtilis 4) Aspergillus oryzae Column II P) Ropiness Q) Koji R) Glycosides S) Porphyrins (A) 1-S, 2- R, 3-P, 4-Q (C) 1-Q, 2-S, 3-P, 4-R XE-G (B) 1-R, 2-S, 3-Q, 4- P (D) 1-R, 2-S, 3-P, 4-Q 2/5 GATE 2014 Q.14 FOOD TECHNOLOGY XE-G Make the correct combination of underlying principles in Column I with the processes in Column II Column I 1) Carbonyl derivatives react with free amino acids to yield aldehydes 2) Starch aggregates and forms micro-crystals 3) Starch granules swell and leach amylose 4) Pyranose or furanose rings open up by pyrolytic reactions to form furfural derivatives Column II P) Gelatinization Q) Strecker degradation R) Caramelization S) Retrogradation (C) 1-R, 2-S, 3-P, 4- Q Q.15 (B) 1-Q, 2-S, 3-P, 4-R (D) 1-Q, 2-P, 3- S, 4-R 14 ) (A) 1-Q, 2-R, 3-P, 4- S Which one of the following statements is FASLE? (A) The peptide bond is planar offering restricted rotation around its axis. 20 (B) Full range of water activity is 0 aw 1 and it has well defined unit. (C) The autooxidation of lipids proceeds via free radical mechanism. (D) The carbonyl group of sugar reacts with nucleophilic amino group of amino acids in Q.16 E Amadori rearrangement. Which one of the following statements is TRUE? AT (A) Pectate lyase hydrolyzes methyl ester bond of pectin. (B) -Solanine is a non-toxic compound found in solanaceae plants. (C) Egg proteins have lower digestibility than pea proteins. Fish fillet having 84% moisture (wet basis) is frozen from top using an air blast freezer maintained at 32 C. The initial temperature of the fillet (density 1050 kg m-3) is 2 C (freezing point). Convective heat transfer coefficient of air is 25 Wm-2 K-1, thermal conductivity of frozen fish is 1.0 Wm-1K-1 and latent heat of crystallization is 340 kJ kg-1. The freezing time, in min, for a 20 mm thick block of fish fillet weighing 1 kg is __________ XE Q.17 (G (D) Lipoxygenase catalyses the conversion of cis, cis-1,4-pentadiene to hydroperoxides. Q.18 Make the correct combination of properties in Column I with their dimensions in Column II Column I 1) Dynamic viscosity 2) Thermal conductivity 3) Specific heat 4) Force Column II P) m2 s-2 K-1 Q) kg m s-2 R) kg m-1 s-1 S) kg m s-3 K-1 (A) 1-R, 2-S, 3-Q, 4- P (C) 1-R, 2-S, 3-P, 4-Q XE-G (B) 1- Q, 2-S, 3-P, 4- R (D) 1- S, 2-R, 3-P, 4-Q 3/5 GATE 2014 Q.19 FOOD TECHNOLOGY XE-G The viscosity and density of a fruit juice at 21 C are 6.3 x 10-3 Pa s and 1029 kg m-3, respectively. The juice flows at the rate of 0.12 m3 min-1 in a 2.54 cm inner diameter steel pipe. Correct combination of the Reynolds number (NRe) and the nature of flow of juice is (A) NRe = 1048, Laminar (C) NRe = 16375, Turbulent Q.20 (B) NRe = 2056, Laminar (D) NRe = 28656, Turbulent For a typical food sorption isotherm curve (Figure 1), which one of the following statements is CORRECT ? 14 ) C 25 20 20 15 10 B A 5 0 0.0 E Equilibrium moisture content (%) 30 0.2 0.4 0.6 0.8 1.0 AT Water activity Figure 1: Food sorption isotherm curve (G (A) Y-coordinate of A represents monolayer water content of food, A-B represents water absorbed in the multilayer within the food and B-C represents free water within the capillary network of the food. (B) Y-coordinate of B represents monolayer water content of food, A-B represents water absorbed in the multilayer within the food and B-C represents free water within the capillary network of the food. XE (C) Y-coordinate of A represents monolayer water content of food, Y-coordinate of B represents water absorbed in the multilayer within the food and B-C represents free water within the capillary network of the food. (D) Y-coordinate of A represents monolayer water content of food, A-C represents water absorbed in the multilayer within the food and Y-coordinate of C represents free water within the capillary network of the food. XE-G 4/5 GATE 2014 FOOD TECHNOLOGY XE-G 10,000 kg milk (7% fat) is passed through a cream separator to obtain cream (40% fat) and skim milk (0.1 % fat). The cream, thus obtained, is churned to make butter of 80.5% fat. If a loss of 0.5% of initial milk fat occurs during the manufacturing process, the % overrun is _________________ Q.22 A 50 mm thick pack of farm fresh berries is cooled at one side from 24 C to 7 C. The relevant properties of berries are: density 1025 kg m-3, specific heat 3.78 kJ kg-1K-1, convective heat transfer coefficient 30 Wm-2K-1, and thermal conductivity 0.3 Wm-1 K-1. The Fourier number for a cooling span of 30 min is ________________ 14 ) Q.21 XE (G AT E 20 END OF THE QUESTION PAPER XE-G 5/5

Formatting page ...

Top Contributors
to this ResPaper
(answers/comments)

Rahul Anand
(3)

Rakesh Shukla
(1)

Naveen C.M
(1)

Formatting page ...

Additional Info : GATE 2014 solved question paper of engineering science
Tags : model ques paper 2015, GATE engineering science., India, GATE Exam Question Papers, Free Online Solutions, Answers, Answer Key, Graduate Aptitude Test in Engineering, IIT, IISc, GATE Exam Syllabus, GATE Study Material, GATE Exam Pattern, gate exam papers, gate question papers 2016, 2015, 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007, 2006, 2005, 2004, 2003, 2002, 2001, 2000, 1999, 1998, 1997, 1996, 1995, 1994, 1993, 1992, 1991, past gate papers, gate papers with answers, gate entrance exam engineering, gate previous years papers, gate old papers, gpat.

gate chat

Horizontal lines at:
Guest Horizontal lines at:
AutoRM Data:
Box geometries: