
	Trending ▼ ICSE CBSE 10th ISC CBSE 12th CTET GATE UGC NET Vestibulares ResFinder

NSW HSC 2010 : INDUSTRIAL TECHNOLOGY – Graphics Technologies

14 pages, 17 questions, 0 questions with responses, 0 total responses,

	nsw_hsc	+Fave Message
	Profile Timeline Uploads Q & A

Home > nsw_hsc >

Instantly get Model Answers to questions on this ResPaper. Try now!
NEW ResPaper Exclusive!

Formatting page ...

2010 H I G H E R S C H O O L C E R T I F I C AT E E X A M I N AT I O N Industrial T echnology Graphics T echnologies Total marks 40 General Instructions Reading time 5 minutes 1 Working time 1 hours 2 Write using black or blue pen Draw diagrams using pencil Board-approved calculators may be used Write your Centre Number and Student Number at the top of page 9 S ection I Pages 2 6 10 marks Attempt Questions 1 10 Allow about 20 minutes for this section S ection II Pages 9 12 15 marks Attempt Questions 11 15 Allow about 35 minutes for this section S ection III Page 13 15 marks Attempt Question 16 Allow about 35 minutes for this section 1260 Section I 10 marks Attempt Questions 1 10 Allow about 20 minutes for this section Use the multiple-choice answer sheet for Questions 1 10. 1 What type of pictorial drawing is shown? 45 (A) Axonometric (B) Oblique (C) Orthographic (D) Perspective 2 What does AS1100.301 refer to? (A) Drawing standards used in engineering (B) Australian Schools Standard for drawing (C) Drawing standards used in mechanical drawing (D) Drawing standards used in architectural drawing 2 3 How is a section line in a drawing indicated? (A) (B) (C) (D) 4 A house plan has been drawn to a scale of 1:100. If a measurement is 4.5 metres in real life, how long would it be on the house plan? (A) 4.5 mm (B) 45 mm (C) 450 mm (D) 4500 mm 3 5 A drawing of a metal joint is shown. What type of weld is indicated by the symbol? (A) Butt (B) CT (C) Fillet (D) Single V-butt 6 Which of the following sectional drawings correctly shows a counter-sunk threaded blind hole? (A) (B) (C) (D) 4 Use the floor plan to answer Questions 7 8. X 11.65 m 2.05 m 4.30 m Patio Garage 6.45 m Entry 1.40 m 2.15 m 9.55 m 7 3.10 m 2.90 m What does the symbol indicated at X on the floor plan indicate? (A) Hand basin (B) Kitchen sink (C) Laundry sink (D) Water closet 8 What is the approximate area of the house (including garage, patio and entry) in square metres? (A) 229 m2 (B) 239 m2 (C) 248 m2 (D) 268 m2 5 9 A drawing of a step block is shown with dimensions marked. A B D C Which distance is correctly dimensioned? (A) A (B) B (C) C (D) D 10 Which of the following correctly indicates first-angle projection? (A) (B) (C) (D) 6 BLANK PAGE 7 BLANK PAGE 8 Board of Studies NSW 2010 2 010 HIGHER SCHOOL CER TIFIC ATE EXAMINATION Industrial T echnology Graphics T echnologies Centre Number Section II Student Number 15 marks Attempt Questions 11 15 Allow about 35 minutes for this section Answer the questions in the spaces provided. These spaces provide guidance for the expected length of response. Question 11 (3 marks) Identify TWO advantages and TWO disadvantages of using CAD programs in the production of drawings. ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... 1261 9 3 Question 12 (2 marks) Render the drawing of the billiard ball shown to give a three dimensional effect. There is a light source located behind the ball at 45 . 2 Light source Question 13 (3 marks) Outline the processes used by an architectural firm to develop a design from concept to council submission. ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... 10 3 Question 14 (3 marks) Complete detailed orthographic views of the drawing below. The views are to be drawn to full size. Include overall dimensions and hidden detail lines. 20 40 NOT TO SCALE 10 10 20 10 20 40 20 11 3 Question 15 (4 marks) 4 A drawing of a machine block is shown. Sketch a full size isometric view using the starting points indicated. 14 14 14 R10 10 20 NOT TO SCALE 10 45 10 10 Top View 100 50 Side View Front View 12 Board of Studies NSW 2010 2 010 HIGHER SCHOOL CER TIFIC ATE EXAMINATION Industrial T echnology Graphics T echnologies Section III 15 marks Attempt Question 16 Allow about 35 minutes for this section Answer the question in a writing booklet provided. Extra writing booklets are available. Question 16 (15 marks) A small family-owned company is operating successfully in a local market. The company is assessing the feasibility of relocating to a larger facility in order to expand production. (a) Outline environmental considerations that may affect the expansion of the company. 3 (b) Analyse the structural, technical and personnel issues to be considered prior to relocating and expanding. 12 End of paper 1262 13 BLANK PAGE 14 Board of Studies NSW 2010

Formatting page ...

Additional Info : New South Wales Higher School Certificate Industrial Technology Papers
Tags : australia new south wales, nsw hsc online, nsw hsc past papers, nsw hsc papers, nsw hsc syllabus, nsw board of studies, higher school certificate new south wales, nsw australia, hsc syllabus, nsw hsc exams, nsw hsc question papers, nsw hsc solved question papers, nsw hsc previous exam papers, nsw university.

nsw_hsc chat

Horizontal lines at:
Guest Horizontal lines at:
AutoRM Data:
Box geometries: