
	Trending ▼ ICSE CBSE 10th ISC CBSE 12th CTET GATE UGC NET Vestibulares ResFinder

NSW HSC 2010 : INDUSTRIAL TECHNOLOGY – Timber Products and Furniture Technologies

14 pages, 18 questions, 0 questions with responses, 0 total responses,

	nsw_hsc	+Fave Message
	Profile Timeline Uploads Q & A

Home > nsw_hsc >

Instantly get Model Answers to questions on this ResPaper. Try now!
NEW ResPaper Exclusive!

Formatting page ...

2010 H I G H E R S C H O O L C E R T I F I C AT E E X A M I N AT I O N Industrial T echnology Timber Products and Furniture Technologies Total marks 40 General Instructions Reading time 5 minutes 1 Working time 1 hours 2 Write using black or blue pen Draw diagrams using pencil Board-approved calculators may be used Write your Centre Number and Student Number at the top of page 9 S ection I Pages 2 5 10 marks Attempt Questions 1 10 Allow about 20 minutes for this section S ection II Pages 9 12 15 marks Attempt Questions 11 16 Allow about 35 minutes for this section S ection III Page 13 15 marks Attempt Question 17 Allow about 35 minutes for this section 1290 Section I 10 marks Attempt Questions 1 10 Allow about 20 minutes for this section Use the multiple-choice answer sheet for Questions 1 10. 1 What type of screw is the most suitable to achieve a flush fitting surface in timber? (A) Countersunk (B) Pan head (C) Raised head (D) Round head 2 What is the most suitable timber adhesive for furniture that is going to be used outdoors? (A) Contact (B) Hot melt glue (C) Polyvinyl acetate (D) Resorcinol formaldehyde 3 What is marquetry? (A) A decorative edge treatment (B) An initial step in marking out timber for cutting (C) A wood carving technique that results in a 3D image (D) The process of cutting and fitting veneers together to form a design 4 Which of the following hand tools will produce the smoothest timber finish? (A) Hand scraper (B) Block plane (C) Smoothing plane (D) Cork block and 80 grit garnet paper 2 5 Which of the following diagrams shows a halving joint? (A) (C) 6 (B) (D) Which of the following conversion processes will produce the most stable board? (A) Back sawn (B) Quarter sawn (C) Rotary peel (D) Through sawn 7 Which of the following manufactured boards has uniform strength in both directions? (A) Coreboard (B) Blockboard (C) Composite board (D) Medium density fibreboard 8 How do you prevent splitting when nailing near the ends of hardwood? (A) Use a bradawl. (B) Drill a pilot hole. (C) Use small diameter nails. (D) Drive the pointed end of a marking knife into the wood. 3 9 The diagram shows the details of a drawer. All measurements are in millimetres. Part Length Width Thickness Quantity Drawer front 400 190 19 1 Drawer side 450 190 12 2 Drawer back 380 175 12 1 Drawer base 440 380 3 1 Material costs 190 19 hoop pine costs $8.50 per metre 190 12 hoop pine costs $8.25 per metre 440 380 3 plywood costs $0.25 per piece What is the total cost of the materials required to produce one drawer? (A) $13.86 (B) $14.11 (C) $14.21 (D) $14.53 4 19 A diagram and details of a cabinet door are shown. TOP 480 CABINET DOOR 550 V-grooved shiplap 90 12 65 10 65 FRONT Material costs 140 19 hoop pine costs $7.50 per metre 70 12 hoop pine costs $6.50 per metre 140 12 hoop pine costs $6.50 per metre 70 19 hoop pine costs $3.80 per metre What is the most cost effective timber order for the cabinet door frame? (A) 1 1800 70 19 (B) 1 1800 70 12 (C) 1 900 140 19 (D) 1 900 140 12 5 BLANK PAGE 6 BLANK PAGE 7 BLANK PAGE 8 Board of Studies NSW 2010 2 010 HIGHER SCHOOL CER TIFIC ATE EXAMINATION Industrial T echnology Timber Products and Furniture Technologies Section II Centre Number Student Number 15 marks Attempt Questions 11 16 Allow about 35 minutes for this section Answer the questions in the spaces provided. These spaces provide guidance for the expected length of response. Questions 11 16 refer to the diagram of an entertainment unit below. The unit is to be manufactured as a flat pack . Question 11 (1 mark) Sketch a knockdown fitting that could be used. 1291 9 1 Question 12 (2 marks) What are the advantages of producing the entertainment unit as a flat pack ? 2 ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... Question 13 (2 marks) The details of a glass door frame from the entertainment unit are shown. A Name and describe, with the aid of sketches, a suitable framing joint that could be used in the area marked at A in the door frame. ............................................................. ............................................................. ............................................................. ............................................................. ............................................................. ............................................................. ............................................................. 10 2 Question 14 (3 marks) Describe the safety precautions that need to be considered when constructing and finishing cabinet furniture made from manufactured boards. 3 ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... Question 15 (3 marks) What are the advantages and disadvantages of using solid timber as opposed to manufactured board for the top of the entertainment unit? ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... 11 3 Question 16 (4 marks) Describe techniques used when making furniture from manufactured boards. ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... ......................................................................................................................................... 12 Board of Studies NSW 2010 4 2 010 HIGHER SCHOOL CER TIFIC ATE EXAMINATION Industrial T echnology Timber Products and Furniture Technologies Section III 15 marks Attempt Question 17 Allow about 35 minutes for this section Answer the question in a writing booklet provided. Extra writing booklets are available. Question 17 (15 marks) A small family-owned company is operating successfully in a local market. The company is assessing the feasibility of relocating to a larger facility in order to expand production. (a) Outline environmental considerations that may affect the expansion of the company. 3 (b) Analyse the structural, technical and personnel issues to be considered prior to relocating and expanding. 12 End of paper 1292 13 BLANK PAGE 14 Board of Studies NSW 2010

Formatting page ...

Additional Info : New South Wales Higher School Certificate Industrial Technology Papers
Tags : australia new south wales, nsw hsc online, nsw hsc past papers, nsw hsc papers, nsw hsc syllabus, nsw board of studies, higher school certificate new south wales, nsw australia, hsc syllabus, nsw hsc exams, nsw hsc question papers, nsw hsc solved question papers, nsw hsc previous exam papers, nsw university.

nsw_hsc chat

Horizontal lines at:
Guest Horizontal lines at:
AutoRM Data:
Box geometries: