
	Trending ▼ ICSE CBSE 10th ISC CBSE 12th CTET GATE UGC NET Vestibulares ResFinder

GCE MAY 2009 : AS 3, Practical Techniques (Internal Assessment) Session 1- Revised

20 pages, 23 questions, 0 questions with responses, 0 total responses,

	gce	+Fave Message
	Profile Timeline Uploads Q & A

Home > gce >

Instantly get Model Answers to questions on this ResPaper. Try now!
NEW ResPaper Exclusive!

Formatting page ...

Sp ec Ne i w ca tio n Centre Number 71 Candidate Number ADVANCED SUBSIDIARY (AS) General Certificate of Education 2009 Physics Assessment Unit AS 3 AY131 assessing Practical Techniques (Internal Assessment) Session 1 [AY131] WEDNESDAY 13 MAY, MORNING TIME 1 hour 30 minutes. INSTRUCTIONS TO CANDIDATES Write your Centre Number and Candidate Number in the spaces provided at the top of this page. Turn to page 2 for further Instructions and Information. For Teacher s use only Question 5(a)(i) YES Was the candidate told which graph to plot? NO Marks Question Number Teacher Examiner Mark Check 1 2 3 4 5 Total Marks 4993 INSTRUCTIONS TO CANDIDATES Answer all the questions in this booklet. Rough work and calculations must also be done in this booklet. Except where instructed, do not describe the apparatus or experimental procedures. The Teacher/Supervisor will tell you the order in which you are to answer the questions. One hour is to be spent on Section A and 30 minutes on Section B. Section A consists of four short experimental tests. You will have access to the apparatus for 13 minutes for each of the tests. At the end of this 13-minute experimental period there is a 2-minute changeover to the area set aside for the next test. Any spare time before the start of the next test may be used to write up anything you have not yet completed. At the end of your Section A work you will be told to move to the area set aside for Section B. Section B consists of one question in which you will analyse a set of experimental results. INFORMATION FOR CANDIDATES The total mark for this paper is 40. Section A and Section B carry 20 marks each. Figures in brackets printed down the right-hand side of pages indicate the marks awarded to each part question. You may use an electronic calculator. 4993 2 [Turn over BLANK PAGE 4993 3 [Turn over Section A 1 Teacher Examiner Remark Mark Check In this experiment you are to investigate the path of light as it travels from air into a plastic block and emerges from the other side. You are provided with a rectangular plastic block, a raybox, a protractor and a ruler. (a) Place the plastic block on Fig. 1.2 on the opposite page and mark its outline. The block should be as indicated in Fig. 1.1. Block Fig. 1.1 Remove the block and draw a normal near the middle of one of the longer sides of the block. Then draw a line representing an incident ray at an angle of incidence i of 20 . Replace the block on its outline on the paper. Place the raybox to direct a ray of light along the line drawn. Mark the path of the emergent ray. Remove the block and construct the path of the ray through the block. Repeat this procedure for an angle of incidence i of 40 , using the same normal line. [3] 4993 4 [Turn over Fig. 1.2 4993 5 [Turn over (b) Use your diagram to make measurements of the angles of refraction r on entry into the block. Teacher Examiner Remark Mark Check Record the angles of refraction in Table 1.1. Table 1.1 Angle of incidence i/ Angle of refraction r/ 20 40 Use your results to obtain an average value of the refractive index of the plastic of which the block is made. Space has been left in Table 1.1 for you to enter any additional values you may need to calculate. You are advised to show your working clearly. Refractive index of plastic = ________________ 4993 6 [2] [Turn over BLANK PAGE (Questions continue overleaf) 4993 7 [Turn over 2 In this experiment you are to obtain an accurate value for the period of oscillation of a pendulum, and to investigate how the period depends on the length of the pendulum. Teacher Examiner Remark Mark Check Fig. 2.1 shows the arrangement of the apparatus, which has already been set up for you. x A Fig. 2.1 (side view) B Fig. 2.2 (front view) The pendulum bob is suspended by a string inserted in a split cork. The length of the string can be adjusted by pulling it through the cork. The length is measured between the point of suspension and the centre of the pendulum bob. The length can be measured with the metre rule. The period of oscillation is the time taken for the pendulum to swing from A to B and back to A, as shown in Fig. 2.2. (a) Using the rule, check that the length x is 15 cm. Using small oscillations, determine the period of oscillation T of the pendulum. Record all your results in Table 2.1. Head the blank column appropriately. Table 2.1 x/cm T/s 15 30 45 Repeat the procedure for values of the length x of 30 cm and 45 cm. [3] 4993 8 [Turn over (b) It is suggested that the relationship between the length x and the period of oscillation T of the pendulum is given by T = kxn Teacher Examiner Remark Mark Check Equation 2.1 where k and n are constants. Using your results in Table 2.1, choose a possible value for n in Equation 2.1. Indicate your choice by placing a tick ( ) in the appropriate box. Explain your answer. n=1 1 n= 2 n = 2 Explanation: ______________________________________________ __________________________________________________________ _______________________________________________________ [2] 4993 9 [Turn over 3 In this experiment you are to measure the wall thickness of a piece of copper pipe. Teacher Examiner Remark Mark Check (a) Use the vernier calipers to measure the external diameter E and the internal diameter I of the pipe, as shown in Fig. 3.1. E I Fig. 3.1 Record all your readings in the spaces below. External diameter E = __________ mm Internal diameter I = __________ mm Use these values to determine the thickness t of the copper walls of the tube. Thickness t = __________ mm 4993 [4] 10 [Turn over (b) Calculate the absolute uncertainty in your value of the thickness t. Consider only the uncertainty due to reading the calipers. Absolute uncertainty = __________ mm 4993 11 Teacher Examiner Remark Mark Check [1] [Turn over 4 In this experiment you are provided with a sealed box fitted with four terminals A, B, C, D. Fig. 4.1 shows three possible arrangements of identical resistors inside the sealed box. A A B D C A B D C Arrangement 1 B D C Arrangement 2 Arrangement 3 Fig. 4.1 One of these arrangements of resistors is inside the box. You are to find which arrangement it is. You are also provided with a pre-connected test circuit containing a power supply, an ammeter, a voltmeter and connecting leads, as shown in Fig. 4.2. A V Fig. 4.2 4993 12 [Turn over (a) Use the test circuit to take readings of current I and voltage V for each of the connections AD, BD and CD. Record your readings in Table 4.1. Teacher Examiner Remark Mark Check Table 4.1 AD BD CD I/mA V/V R/ Calculate the corresponding resistance R for each connection, and include this in Table 4.1. [3] (b) Deduce which of the arrangements in Fig. 4.1 is contained in the box. Indicate your choice by placing a tick ( ) in the appropriate box. Explain your answer. You are advised to show your working clearly. The box contains the arrangement of resistors shown in Arrangement 1 Arrangement 2 Arrangement 3 Explanation _______________________________________________ __________________________________________________________ __________________________________________________________ _______________________________________________________ [2] 4993 13 [Turn over Section B Teacher Examiner Remark Mark Check Data Analysis question 5 Acceleration of free fall on the Earth s surface A student uses laboratory apparatus to determine a value for the acceleration of free fall on the Earth s surface, g. A ball bearing is dropped from rest from a height h. The height through which the ball falls is varied by the student. The student measures this height with a metre rule. The time t taken for the ball to fall is measured using an electronic timing device. Results The student takes a set of values of t corresponding to different values of h. The student records the results in Table 5.1. Table 5.1 h/cm t/s 30.0 0.249 40.0 0.293 50.0 0.319 60.0 0.351 70.0 0.378 80.0 0.400 / The student plans to apply the standard equation of motion 1 s = ut + at 2 2 Equation 5.1 where s is the distance travelled, u is the initial velocity, a is the acceleration and t is the time taken, to these results. 4993 14 [Turn over (a) (i) What graph should be plotted so as to give a straight line from which g can be obtained? State the horizontal (x) and vertical ( y) axes. Teacher Examiner Remark Mark Check Horizontal axis: _______________ Vertical axis: _______________ [2] If you are unable to work out what graph is required, you may ask for assistance. A deduction of 2 marks will be made. (ii) Explain how the value of g may be obtained from the graph in (a)(i). ______________________________________________________ ___________________________________________________ [1] 4993 15 [Turn over Data processing Teacher Examiner Remark Mark Check (b) (i) Head the blank column of Table 5.1 with the quantity that should be calculated to draw the graph in (a)(i). Include appropriate units. [2] (ii) Calculate the numerical values required to complete the blank column in Table 5.1 to an appropriate number of significant figures. [2] (iii) On the grid of Fig. 5.1 opposite, draw the graph of the processed data in Table 5.1. Label the axes in the boxes provided and choose suitable scales. Plot the points and draw the best-fit straight line. [5] Analysis (c) (i) Measure the gradient of your graph in (b)(iii), showing your working clearly. Include an appropriate unit. Gradient = _______________ Unit: _______________ [3] (ii) Hence calculate your value of g. Give your answer in m s 2. g = _______________ m s 2 4993 [1] 16 [Turn over / Fig. 5.1 4993 17 / [Turn over Evaluation Teacher Examiner Remark Mark Check (d) (i) The student s data sheet gives the value of g as 9.81 m s 2. Calculate the percentage difference between this value and your value in (c)(ii). Percentage difference in values of g = ___________ % [2] (ii) Explain how, using your graph, an upper limit could be placed on the value of g. Find this upper limit. Explanation: ______________________________________________________ ______________________________________________________ Upper limit on value of g = __________ m s 2 4993 18 [2] [Turn over THIS IS THE END OF THE QUESTION PAPER 938-067-1 20

Formatting page ...

Additional Info : Gce Physics May 2009 Assessment Unit AS 3, Practical Techniques (Internal Assessment) Session 1 - Revised
Tags : General Certificate of Education, A Level and AS Level, uk, council for the curriculum examinations and assessment, gce exam papers, gce a level and as level exam papers , gce past questions and answer, gce past question papers, ccea gce past papers, gce ccea past papers

gce chat

Horizontal lines at:
Guest Horizontal lines at:
AutoRM Data:
Box geometries: