Trending ▼   ResFinder  

2nd National Certification Exam Energy Managers & Auditors 2005 Paper 2

11 pages, 82 questions, 0 questions with responses, 0 total responses,    0    0
bee_energy
Jawaharlal Nehru Technological University (JNTUH), Hyderabad
+Fave Message
 Home > bee_energy >   F Also featured on: reddyram

Instantly get Model Answers to questions on this ResPaper. Try now!
NEW ResPaper Exclusive!

Formatting page ...

Paper 2 Set A NATIONAL CERTIFICATION EXAMINATION 2005 FOR ENERGY MANAGERS & ENERGY AUDITORS Question Papers & Model solutions to the Question Papers PAPER 2: Energy Efficiency in Thermal Utilities Date: 28.05.2004 Timings: 1400-1700 HRS Duration: 3 HRS Max. Marks: 150 General instructions: o o o o o Please check that this question paper contains 7 printed pages Please check that this question paper contains 65 questions The question paper is divided into three sections All questions in all three sections are compulsory All parts of a question should be answered at one place Section I: OBJECTIVE TYPE (i) (ii) (iii) 1. Answer all 50 questions Each question carries one mark Put a ( ) tick mark in the appropriate box in the answer book 0 Specific heat in kCal/kg - C of fuel oil is in the range of a) 0.15 0.20 2. b) 0.22 0.28 c) 0.29 0.32 d) none of the above Grade B Indian coal has a energy content range (in kcal/kg) of a) 3360-4200 3. Marks: 50 x 1 = 50 b) 4200-4900 c) 4940-5600 Which is the common coal firing system used in Indian thermal power plants? a) pulverized coal firing b) stoker firing c) fluidized bed 4. b) Propane b) 3.2 d) Coal c) 6 d) 18 Which fuel releases the most energy per kg on complete combustion a) Carbon 7. c) Hydrogen Stochiometric air required for combustion of Bagasse is about a) 13.7 6. d) pressurized bed Which of the following fuel requires maximum air for stochiometric combustion? a) Butane 5. d) 5600-6200 b) Sulphur c) Nitrogen d) Hydrogen How many kg of CO2 are produced in complete combustion of 16 kg of Methane? a) 42 b) 44 _________________________ Bureau of Energy Efficiency c) 16 d) none of the above 1 Paper 2 Set A 8. In flue gas the theoretical CO2 is 15.5% and measured CO2 is 11% by volume. The percentage of excess air will be a) 40.9% 9. c) 240.9 % d) 140.9 % Evaporation ratio (steam to fuel ratio) of an oil fired efficient boiler is in the range of a) 5 - 6 10. b) 38.7 % b) 13 14 d) 7 9 c) 1 - 3 A rise in conductivity of boiler feed water indicates a) drop in the total dissolved solids in boiler water b) more steam generation c) greater purity of feed water d) rise in the total dissolved solids in boiler water 11. De-aeration of boiler feed water is referred to as a) removal of dissolved gases c) removal of TDS from feed-water 12. 0 Pre-heating of combustion air in an oil fired furnace by 20 C will save about ___% of fuel a) 0.3 13. b) 1 d) 0.6 b) bimetallic d) none of the above 0 Increase in stack gas temperature of 22 C due to tube fouling or other causes will increase oil consumption in an oil fired boiler by about. a) 1% 15. c) 1.5 To drain condensate from main steam line, the following type of trap is a suitable trap. a) float c) thermodynamic 14. b) removal of silica from feed-water d) phosphate treatment of feed-water b) 2% c) 3% d) 4% Water hammer in a steam system is caused by a) collected condensate hitting obstructions b) leaking pipe joints c) slow moving steam d) continuous slope in direction of flow 16. Which data is not required to calculate boiler efficiency by the indirect method a) steam flow rate c) ambient temperature 17. Latent heat at the critical point of a steam phase diagram is a) infinite 18. b) stack gas temperature d) energy content of fuel b) 540 kCal/kg c) zero d) none of the above Increase of steam pressure has the following effect on steam: a) steam temperature goes up and enthalpy of evaporation goes down b) steam temperature and enthalpy of evaporation go down c) steam temperature goes up and enthalpy of evaporation goes up d) specific volume goes down and enthalpy of evaporation goes up 19. Scale losses in reheating furnaces will increase with a) decrease in excess air c) increase with excess air _________________________ Bureau of Energy Efficiency b) decrease in furnace temperature d) are not correlated to temperature 2 Paper 2 Set A 20. An air film inside a steam pipe, made of steel may be _______ times more resistant to heat transfer than the steam pipe. a) 200 1000 b) 1500 3000 c) 4000 8000 d) 8000 16000 21. The best steam for indirect heating in most industrial process is a) as dry as possible b) super heated steam c) wet steam d) as wet as possible 22. Pressure drop through a steam pipe is inversely proportional to a) diameter 23. b) square of diameter c) fifth power of diameter In an oil fired burner, the excess air level _____ towards the highest turndown ratio for efficient combustion. a) decreases 24. d) cube of diameter b) increases c) not affected d) none of the above What is the most effective way to avoid ambient air infiltration into a continuous furnace a) close all openings b) increase the chimney height c) operate at about 90% capacity d) reduce negative pressure inside the furnace 25. Black body radiation is a) linear proportional to temperature b) proportional to the fourth power of the temperature of the body c) proportional to the fourth power of the absolute temperature of the body d) proportional to the square of the body surface area 26. Steam at 6 bar has a sensible heat of 159.33 kCal/ kg and latent heat of 498.59 kCal/ kg. If the steam is 95% dry than the total enthalpy is a) 625 kCal/ kg 27. b) 649.95 kCal/ kg b) continuous Hoffmann tunnel kiln d) low temperature furnace 0 Which loss is the highest in a typical re-heating furnace operating at 1300 C? a) flue gas loss b) wall loss 29. d) 633 kCal/ kg In which type of furnace operation is a low mass ceramic fiber insulation most suitable to reduce specific fuel consumption a) batch type furnace c) rotary high temperature furnace 28. c) 553 kCal/ kg c) necessary opening loss d)cooling water loss In a batch type furnace the following energy efficiency measure would be the most controversial a) increasing the insulation at the hot temperature side b) increasing the insulation at the outer surface of the furnace c) pre-heating the combustion air d) reducing excess air. 30. Pick the wrong statement. The thermal efficiency of a furnace increases by a) preheating combustion air c) reducing the surface heat loss _________________________ Bureau of Energy Efficiency b) increasing the excess air flow rate d) minimizing the CO loss and un-burnt losses 3 Paper 2 Set A 31. The most economic insulation is the thickness where .. a) depreciation costs of insulation and energy cost due to losses are the same b) the sum of energy cost due to losses and insulation depreciation cost is minimum c) energy losses are minimized d) energy cost due to losses are minimized. 32. Which of the four refractories has the highest melting point temperature? a) Lime (CaO) b) Silica (SiO2 ) 33. c) Titania (TiO2 ) d) Alumina (Al2 O3 ) The emissivity of refractory material . 0 a) increases sharply above 1000 C b) will be more or less independent of temperature c) will increase with increasing temperature d) will decrease with increasing temperature 34. High emissivity coatings are applied on a) outer surface of furnace c) inner surface of furnace 35. The heat loss rate from a surface is expressed in 2 0 2 b) Watt/m K a) Watt 36. b) refrigeration piping d) none of the above 0 c) Watt/m C d) Joules Which statement is incorrect a) higher density refractory has a lower thermal conductivity b) a higher emissivity means higher radiation of heat c) a higher emissivity means lower absorption of heat d) a black colored body radiates more than a glossy white colored one. 37. Fluidized bed combustion takes place in a temperature range of 0 0 a) 600 C - 700 C 38. b) NOx and SOx c) CO2 b) Limestone d) CO c) Sand d) Silica b) bed tubes d) super heater tubes In glass industry waste heat is used for power generation. This type of cogeneration is called a) topping cycle c) gas turbine cycle 42. 0 d) about 500 C In circulating fluidized bed combustion boilers most of the heat transfer takes place a) inside the combustion zone c) outside of the combustion zone 41. 0 c) above 1000 C SOx emissions in a FBC boiler fired with high sulfur coal are controlled by adding ____ to the bed a) Magnesia 40. 0 The low combustion temperatures in fluidized bed combustion boilers results in minimal formation of a) NOx 39. 0 b) 850 C - 950 C b) bottoming cycle d) none of the above. The unit for heat-to-power ratio of a CHP plant is a) kWth / kWe b) BTU / kW _________________________ Bureau of Energy Efficiency c) kCal / kW d) kWhth / kW e 4 Paper 2 Set A 43. Which CHP system has the smallest heat to power ratio with the least flexibility to increase or reduce the ratio? a) back pressure turbine b) combined cycle c) extraction condensing steam turbine d) reciprocating engine 44. Air compressor alone consumes about ______ of the energy generated in a gas turbine a) 20-30% 45. b) 30-40% d) 50-60% Regenerators utilizing waste heat are widely used in a) cement industry c) glass melting furnaces 46. c) 40-50% b) pulp and paper d) aluminium Heat wheels are mostly used in a situation of . a) high temperature exhaust gases b) heat exchange between large masses of air having small temperature differences c) heat transfer between a liquid and gas d) corrosive gases 47. A heat pipe can transfer up to ____ times more thermal energy than copper a) 10 48. b) 20 b) 10 c) 15 0 C and therefore saves d) 20 A shell and tube heat exchanger is most suitable if a) a liquid is heating another liquid c) a gas is heating a liquid 50. d) 100 An economizer raises the boiler feed water by 60 approximately ___ % of fuel. a) 5 49. c) 50 b) a gas is heating another gas d) the hot gas is loaded with dust The working fluid of a steam thermo-compressor is a) air b) low pressure steam c) high pressure steam d) water -------- End of Section - I --------- Section - II: SHORT DESCRIPTIVE QUESTIONS Marks: 10 x 5 = 50 (i) Answer all Ten questions (ii) Each question carries Five marks S-1 (i) State the stochiometric combustion equation for Methane. (ii) how many kg of Carbon Dioxide are generated by complete combustion of 1 kg of Methane? (iii) how many kg of water are generated by complete combustion of 1 kg of Methane? (i) CH4 + _________________________ Bureau of Energy Efficiency 2O2 = CO2 + 2H2 O 5 Paper 2 Set A (ii) (iii) S-2 16 kg + 64 kg = 44 kg + 36 kg i.e. 2.75 kg of CO2 from 1 kg of Methane 2.25 kg of water from 1 kg of Methane. Assume the stochiometric (theoretical) air to fuel ratio of furnace oil is 14. The burner operates at 20% excess air. Calculate the mass of stack gas generated from combustion of one kg of oil. Mass of air + mass of fuel = mass of stack gas 1.2 x 14 + 1 = 17.8 kg S-3 (i) (ii) Explain the difference between a water tube and a fire tube boiler. In what pressure range have water tube boilers an advantage over fire tube boilers and why? (i) In a fire tube boiler combustion gases are inside small fire tubes, which are bundled, and the water to be heated is outside. In a water tube boiler the water is flowing inside tube bundles and the combustion gases are flowing around the water tubes. (3 marks) At steam pressures of more than 20 bar and larger capacities water tube boilers are preferred, because the thickness of a fire boiler shell would be very thick and heavy to withstand the pressure. (ii) S-4 (i) Explain the meaning of hf , hfg and hg in a water and steam system (ii) Write down the equation for hg if the steam is wet and contains 4% moisture. (i) (ii) S-5 hf = enthalpy of saturated water hfg = enthalpy of evaporation of saturated water to saturated steam hg = enthalpy of saturated steam hg = hf + 0.96 hfg A furnace output is 5000 kg/hour of billets. Thermal efficiency is claimed to be 25% Specific heat of billet is 0.12 kcal/kg-oC. Billets enter the furnace at 40oC and leave at 1200oC. Calculate the hourly oil consumption in liter if GCV of oil is 9,200 kCal/liter. (i) Efficiency = heat absorbed in the stock = 0.25 heat in fuel = 5000 x 0.12 (1200- 40) Liter x 9,200 = 0.25 Liter = 302.6 liter of oil per hour. S-6 In selection of a refractory which physical, chemical and other properties of a refractory are important? (i) (ii) (iii) melting or softening point bulk density, porosity _________________________ Bureau of Energy Efficiency 6 Paper 2 Set A (iv) (v) (vi) S-7 List advantages of fluidized bed combustion boiler over fixed grate boiler. (i) (ii) (iii) (iv) (v) (vi) (vii) (viii) (ix) S-8 thermal conductivity creep at high temperature capital costs efficiency is not so much affected when firing higher ash fuels better fuel flexibility burns low grade fuels burns fines reduces NOx formation may reduce SOx formation through additives no clinker formation no soot blowing quicker response to changing demand What parameters are analyzed in a proximate analysis of coal? The elements analyzed in proximate analysis of coal are (i) ash, (ii) moisture, (iii) volatile matter and (iv) fixed carbon content on a (v) percentage weight basis. S-9 Draw a sketch of an extraction-condensing turbine cogeneration system. S-10 A firm wants to recover the waste heat in a flue gas stream of 2000 kg/hour. from a furnace. Specific heat of flue gas is 0.25 kcal/kg 0C. (i) (ii) calculate the heat recovered if the heat exchanger has an efficiency of 98% and temperature of flue gas drops from 8000 C to 2500 C across the heat exchanger. How many liters of water per hour can be heated by 50 0C from this waste stream? = 2,000 x 0.98 x0.25 x (800 250) = 269,500 kCal / hour (i) Heat transferred to water (ii) Solve for liter the equation 269,500 = liter x 1 kCal x 50 liter = 5,390 liters / hour. _________________________ Bureau of Energy Efficiency 7 Paper 2 Set A -------- End of Section - II --------Section - III: LONG DESCRIPTIVE QUESTIONS Marks: 5 x 10 = 50 (i) Answer all Five questions (ii) Each question carries Ten marks L-1 It is proposed to replace an oil-fired boiler of 10 tons per hour with a coal fired boiler of equivalent capacity. With the help of the data provided find out the following: (i) (ii) (iii) (iv) (v) the annual oil consumption in tons per year? the annual coal consumption in tons per year? estimate annual fuel cost savings in Crore rupees simple pay back period of the project, assuming the coal fired boiler costs Rs.1.5 Crore and annual repair and maintenance costs is 25% of capital cost. What additional data could be added for working out a more realistic simple pay back period? Operation data Heat content of steam - 660 kCal/kg. Feed water inlet temperature - 600 C Daily operating hours - 24 Number of days / year - 300 Efficiency of oil fired boiler - 82% Efficiency of coal fired - 72% Cost of oil - Rs.13/- kg. Cost of coal - Rs.2 /kg. GCV of oil 10,000 kCal/kg GCV of coal 4,200 kCal/kg. (i) the hourly oil consumption is = 10,000 kg x(660-60) = 731.7 kg/h 10,000 kCal x 0.82 it follows 731.7 x 24 x 300/1000 = 5,268 tons per year (ii) the hourly coal consumption is = 10,000 kg x (660-60) = 1,984 kg/h 4200 x 0.72 it follows 1,984 x 24 x300/1000 = 14,285 tons/year (iii) (iv) (5,268 x13,000 14,285 x 2000)/10,000,000 = Rs 3.99 Cr Simple pay back period 1.5/(3.99-0.25 x 1.5) = 0.41 years (vi) The simple payback period in fact cannot be calculated with these few simplistic assumptions because when switching from oil to coal there are additional costs and benefits such as (a) labour (b) coal processing (c) avoided R & M of oil operation (d) salvage value of oil boiler _________________________ Bureau of Energy Efficiency 8 Paper 2 Set A L-2 (i) draw the steam phase diagram in a coordinate system with temperature as (y-axis) and enthalpy as (x-axis) (ii) explain the major regions of the diagram. (i) (ii) Comments a) b) c) d) to the left of the tilted dome is the liquid region under the dome is the two phase region, which means wet steam to the right of the dome is the superheat steam region the highest point of the dome is the super critical point at 374o C and 221 bar e) above the critical point is the super critical region where steam has no well defined boiling points. f) at any point on the dome curve the first x-coordinate B is enthalpy of the saturated liquid, the second x-coordinate C is the enthalpy of the saturated steam and the width C-B is the enthalpy of evaporation from saturated water to saturated steam . L-3 An energy manager recommends to his superior that in an already well functioning boiler the oil be mixed and should contain 20% water by weight. The manager claims: (i) this would reduce fuel costs (ii) boiler efficiency would also improve Agree or disagree and support your decision by argumentation as well as some calculations. Assume that 1 kg of feed water requires about 600 kCal to evaporate. (i) One should disagree because 1 kg of furnace oil is replaced by a mixture of 0.8 k of oil and 0.2 kg of water. Even if water costs are _________________________ Bureau of Energy Efficiency 9 Paper 2 Set A assumed to be zero 1 kg of oil-water mixture cannot cost less than 80% of 1 kg oil. (ii) One should disagree because this means energy in the oil is required to evaporate additional 0.2 kg of water and heat the water vapor (steam) up to the furnace flue gas temperature. This energy is not any longer available to generate steam. The thermal efficiency is therefore reduced and not improved. To heat up and evaporate 1 kg of water about 600 kCal of energy are required. In other words 120/8000 = 1.5% of the energy in the oil-water mixture are needed to evaporate this water. This energy is not any longer available to generate steam. Consequently the boiler efficiency is reduced by at least 1.5 %. L-4 (i) (ii) (iii) (iv) state two examples of heat pump applications in which situation are heat pumps most promising? draw the schematics of a heat pump system briefly discuss each process stage (i) (a) space heating system, (b) use in plastic factory where chilled water is used to cool injection moulding machines, (c) drying applications such as maintaining dry atmosphere in storage and drying compressed air (ii) In a situation when both the cooling and heating capabilities of the cycle can be used in combination (iii) _________________________ Bureau of Energy Efficiency 10 Paper 2 Set A (iv) L-5 Step 1: in the evaporator the heat is extracted to boil the circulating working fluid Step 2: the evaporated working fluid is compressed in a compressor rising working fluid temperature and pressure Step 3: the heat is delivered to the condenser Step 4: the pressure of the working fluid is reduced in a throttling valve and condensate returned to the compressor On the topic of waste heat recovery boilers, explain the following: (i) (ii) (iii) (iv) Which are typical applications of waste heat boilers? How do they differ from ordinary steam boilers? In what temperature range do they operate? Is it more energy efficient to generate hot water of 800 C or saturated steam at 6 bar in a waste heat boiler? Explain (i) Typical applications are to recover waste heat from medium temperature waste gas streams such as (a) gas turbines, (b) incinerators, (c) furnaces. (ii) Waste heat boilers are of the water tube type. The hot gases pass over a number of parallel tubes. There is no radiation section but heat transfer is accomplished by convection only. Some have finned water tubes to increase heat transfer (iii) Gas temperatures are low to medium (400 C to 800 C) (iv) It is more energy efficient to generate hot water at 80 C than saturated steam at 6 bar because more heat can be extracted from the waste heat stream. In the case of steam generation the waste gas temperature can only be lowered to about 180 C while in the case of hot water the waste heat temperature can be lowered to about 130 or even lower if no excessive Sulfur compounds are present in the flue gas. -------- End of Section - III --------- _________________________ Bureau of Energy Efficiency 11

Formatting page ...

Formatting page ...

Formatting page ...

Formatting page ...

Formatting page ...

Formatting page ...

Formatting page ...

Formatting page ...

Formatting page ...

Formatting page ...

 

  Print intermediate debugging step

Show debugging info


 


Tags : Bureau of Energy Efficiency, BEE, National Productivity Council of India, NPC, Energy Audit, Certified Energy Manager, Certified Energy Auditor, EM & EA, bee papers, bee sample papers, bee books, portal for bee india, bee question bank, bee question papers with answers, bee model test papers, solved board question papers of last year, previous years solved question papers, free online solved question paper, india sample questions papers, last 10 years papers, guess sample questions papers, important questions, specimen / mock papers, 2020, 2019, 2018, 2017, 2016, 2015, 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007, 2006, 2005.  

© 2010 - 2025 ResPaper. Terms of ServiceContact Us Advertise with us

 

bee_energy chat