
	Trending ▼ ICSE CBSE 10th ISC CBSE 12th CTET GATE UGC NET Vestibulares ResFinder

GATE 2013 :Production And Industrial Engineering

18 pages, 65 questions, 0 questions with responses, 0 total responses,

	gate	+Fave Message
	Profile Timeline Uploads Q & A

Home > gate >

Formatting page ...

2013 Question Booklet Code A PI : PRODUCTION AND INDUSTRIAL ENGINEERING Duration: Three Hours Maximum Marks: 100 Read the following instructions carefully. 1. Do not open the seal of the Question Booklet until you are asked to do so by the invigilator. 2. Take out the Optical Response Sheet (ORS) from this Question Booklet without breaking the seal and read the instructions printed on the ORS carefully. If you find that either a. The Question Booklet Code printed at the right hand top corner of this page does not match with the Question Booklet Code at the right hand top corner of the ORS or b. The Question Paper Code preceding the Registration number on the ORS is not PI, then exchange the booklet immediately with a new sealed Question Booklet. 3. On the right hand side of the ORS, using ONLY a black ink ballpoint pen, (i) darken the appropriate bubble under each digit of your registration number and (ii) write your registration number, your name and name of the examination centre and put your signature at the specified location. 4. This Question Booklet contains 16 pages including blank pages for rough work. After you are permitted to open the seal, check all pages and report discrepancies, if any, to the invigilator. 5. There are a total of 65 questions carrying 100 marks. All these questions are of objective type. Each question has only one correct answer. Questions must be answered on the left hand side of the ORS by darkening the appropriate bubble (marked A, B, C, D) using ONLY a black ink ballpoint pen against the question number. For each question darken the bubble of the correct answer. More than one answer bubbled against a question will be treated as an incorrect response. 6. Since bubbles darkened by the black ink ballpoint pen cannot be erased, candidates should darken the bubbles in the ORS very carefully. 7. Questions Q.1 Q.25 carry 1 mark each. Questions Q.26 Q.55 carry 2 marks each. The 2 marks questions include two pairs of common data questions and two pairs of linked answer questions. The answer to the second question of the linked answer questions depends on the answer to the first question of the pair. If the first question in the linked pair is wrongly answered or is not attempted, then the answer to the second question in the pair will not be evaluated. 8. Questions Q.56 Q.65 belong to General Aptitude (GA) section and carry a total of 15 marks. Questions Q.56 Q.60 carry 1 mark each, and questions Q.61 Q.65 carry 2 marks each. 9. Questions not attempted will result in zero mark and wrong answers will result in NEGATIVE marks. For all 1 mark questions, mark will be deducted for each wrong answer. For all 2 marks mark will be deducted for each wrong answer. However, in the case of the linked questions, answer question pair, there will be negative marks only for wrong answer to the first question and no negative marks for wrong answer to the second question. 10. Calculator is allowed whereas charts, graph sheets or tables are NOT allowed in the examination hall. 11. Rough work can be done on the Question Booklet itself. Blank pages are provided at the end of the Question Booklet for rough work. 12. Before the start of the examination, write your name and registration number in the space provided below using a black ink ballpoint pen. Name Registration Number PI-A PI 1/16

Formatting page ...

Additional Info : Solved GATE 2013 production and industrial engineering paper
Tags : gate 2014 model papers, production and industrial engineering., India, GATE Exam Question Papers, Free Online Solutions, Answers, Answer Key, Graduate Aptitude Test in Engineering, IIT, IISc, GATE Exam Syllabus, GATE Study Material, GATE Exam Pattern, gate exam papers, gate question papers 2016, 2015, 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007, 2006, 2005, 2004, 2003, 2002, 2001, 2000, 1999, 1998, 1997, 1996, 1995, 1994, 1993, 1992, 1991, past gate papers, gate papers with answers, gate entrance exam engineering, gate previous years papers, gate old papers, gpat.

gate chat

Horizontal lines at:
Guest Horizontal lines at:
AutoRM Data:
Box geometries: